Polymer based Hold coating product, Easy to apply on SHIP HOLD SURFACE. Slip Barrier Coats HOLD BLOCK is POLYMER BASED non-reactive coating materials which makes thin film barrier on the surface after dry. Due to the formation of RXSOL THIN barrier film on the surface, the cleaning operation after unloading becomes quicker and easier with optimum results.
RXSOL HOLD BLOCK is a Heavy Duty protective Solution for hold of vessels, which carry corrosive and/or messy cargos such as sulfur salt petcock coal, and concentrates. It can be easily removed with itRecommendation Dose for smooth surface :
for Sulphur, Salt, etc 100 Ltrs/Hold for HANDYMAX & 150 Ltrs/Hold for PANAMAX
& for Petcoke, Coal, etc 200 Ltrs/Hold for HANDYMAX & 250 Ltrs/Hold for PANAMAX
This material can be used directly with low-pressure machine or manually by a garden spray pump. in general practice on smooth & clean surface each drum of 210 ltrs cover 2000 to 2500 sq meters while on rough and rusted surfaces require more quantities of materials.
for HANDYMAX (5 Holds) : In general 500 Ltr to 1000 Ltr RXSOL-22-2210-210 require to cover area up to 12 mtrs , i.e approx 1/2 drum to 1 drum of material is sufficient for each hold , while
for PANAMAX (7 Holds) : In general 1000 Ltr to 2000 Ltrs RXSOL-22-2210-210 require to cover full area. , i.e approx 3/4 drum to 1.25 drums of material is sufficient for each hold.
Refer this link for complete set of HOLD CLEANING KIT ::: http://rxmarine.com/Ship-hold-cleaning-kit-set-supplier
- Protect metal against corrosive cargo
- Protect paint against cargo penetration
- Environmentally friendly
- Safe to use in occupied / covered areas
- Reduces turn around times
- Easy to direct spray
- If hold cleaning is to be performed from tank top level only powerful equipment designed for cargo hold cleaning will do the job in a minimum of time.
- Effective cleaning chemicals that can dissolve stains and remove discoloring are required the crew needs to have effective equipment to apply these chemicals from tank top level personal proactive equipment is required depending on type and condition of hold paint chemical that protect the paint may also be needed
- And don’t forget procedures have to be drown up and your
- Crew trained for the job Standardization of equipment and chemical onboard you ship will make life easier for your seaman and save your time
This Emulsion is safe to use , But as a precaution goggles & Protective gloves with mask require before use of this materials.
Precaution : 1 > Deposition of previous cargo / Lime wash should be removed .
2 > Newly Painted surface should be fully cured.
Other Valuable Hold Cleaners :::
Cement Remover RX Hold ::: Highly concentrated and powerful penetrating agents materials which is effectively react with cement to loosen the bonding strength . Best results can obtain on dry surface of cement. RXSOL'S R & D has developed this molecular cement dissolver. Part No.- RXSOL-22-2202-025, Part No.- RXSOL-22-2202-020, Part No.- RXSOL-22-2202-050
Refer this link for complete set of HOLD CLEANING KIT ::: http://rxmarine.com/Ship-hold-cleaning-kit-set-supplier
SLIPcoat supplier in Sohar Muscat Oman, Fujairah Dubai UAE
What is Hold Block and why hold block application is better than LIME WASH?
When aggressive or corrosive dry bulk cargoes—such as fertilizers, salt, coal, or sulphur—come into direct contact with the metal surfaces of ship holds, they can cause rapid corrosion and surface degradation due to chemical reactions. This not only weakens the structural integrity of the vessel but also leads to costly repairs and safety risks.
To prevent such reactions and ensure long-lasting surface protection, a polymer-based protective coating is the ideal solution.
Why Use Polymer based HOLD BLOCK Coating in Cargo Holds?
-
Chemical Resistance
Acts as a barrier against corrosive cargoes, preventing direct metal contact and chemical reaction. -
Easy Application
Applied by brush, roller, or spray before cargo loading. Forms a durable, even protective film. -
Temporary or Voyage-Specific Use
Perfect for short-term voyages carrying highly reactive cargoes, allowing for easy cleaning and reapplication after discharge. -
Prevents Pitting & Rust Formation
Shields steel from moisture, acidic residues, and abrasion, reducing long-term maintenance costs.
Field and Typical Applications of HOLD BLOCK
-
Sulphur
-
Salt
-
Phosphates
-
Urea
-
Coal & Petcoke
-
Cement
-
Bauxite
Why Hold Block is better choice than LIME COATING
-
Polymer-based water-resistant coating
-
Safe on all standard marine metal surfaces
-
Compatible with hold cleaning chemicals
-
Non-reactive, non-toxic, and easy to remove
-
Protects for the entire duration of cargo voyage
Recommended Use of Cargo Hold Block
Apply 1–2 coats uniformly across cargo hold surfaces prior to loading reactive cargo. For enhanced protection, focus on:
-
Tank tops
-
Bulkheads
-
Frames and internal structures
-
Hatch coamings
Cargo Hold Block Available Across Indian UAE Oman coastal:
-
UAE: Dubai, Fujairah, Abu Dhabi, Sharjah, Khor Fakkan
-
Oman: Muscat, Sohar, Duqm, Salalah
-
India: Mumbai, Kandla Mundra Jamnagar Sikka, Kolkata Haldia Paradip, Visakhapatnam, Chennai Manglore
| Product name | RXSOL-22-2210-210 PRELOAD |
| Product type | Slip Barrier Coat RXSOL HOLD BLOCK Resist ( Creating polymer film to protect HOLD surface from Hazardous CARGO ) |
Company Details
RX MARINE INTERNATIONAL
105 , A-wing, BSEL TECH PARK
VASHI , NEW BOMBAY 400705
INDIA
Stock Branch ::: Mumbai, Kandla, Chennai, Ennore, Visakhapatnam, Gangavaram, Kolkata, Haldia, Surat, Fujairah, Muscat
| Phone | +91 22 20871200 / 20871300 / 201871400 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| mail@rxmarine.com |
|
Chemical Name |
Concentration by Percentage |
|
Polyvinyl Alcohol |
5-10 |
|
Contains Emulsified POLYMER |
15 |
| Non classified ingredients | 70 - 75 |
|
Odour |
Odourless |
|
Appearance |
Liquid, clear |
|
Contact with eyes |
Can cause damage to the eyes |
|
Contact with skin |
Can cause damage to the skin |
|
Inhalation |
Vapours or aerosols may cause irritation of eyes, nose and respiratory tract |
|
Ingestion |
The ingestion of significant quantities may cause damage to stomach lining |
|
Environmental Hazards |
None |
|
Human Health Hazards |
Moderates |
|
General |
In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible) (S45) |
|
Inhalation |
Harmful,. supply or remove to fresh air and seek medical advice attention |
|
Skin Contact |
May cause irritation Rinse with running water and soap. Skin care. Remove contaminated clothes. Remove contaminated clothing immediately and drench affected skin with plenty of water. Then wash with soap and water Seek medical advice if necessary Contaminated clothing should be laundered before reuse |
|
Eye Contact |
If substance has got into eyes, immediately wash out with plenty of water for at least 15 minutes ( Flush with running water for at least 15 minutes Immediately . ) Obtain immediate medical attentionContinue flushing with water until medical help arrives |
|
Ingestion |
Vomiting is dangerous , seek medical attention. ( Do not induce vomiting ) Never give anything by mouth to an unconscious person Give plenty of water to drink Obtain immediate medical attention |
Non combustible Decomposition products may include toxic and irritant fumes Not flammable. In case of fire use extinguishing media appropriate to surrounding conditions
|
Suitable |
N.A. can use foam dry Co2 , water-spray. |
|
Not suitable |
Not applicable |
|
Special |
Not applicable |
|
Protection of fire Fighter |
Not applicable |
|
Flashpoint |
> 250º C |
|
Special protective equipment for fire-fighters |
Wear protective equipment. |
|
Personal Precautions |
Wear protective clothing as per section 8 |
|
Environmental Precautions |
Do not allow to enter public sewers and watercourses |
|
Immediate Actions |
Contain spillage by any means possible |
|
Clean Up Actions |
Absorb spillage in inert material and shovel up Ventilate the area and wash spill site after material pick-up is complete |
|
Special Precautions |
Wear protective clothing as per section 8 |
|
Enviromental Precaution |
Direct flow into drainage system, surface or ground water is prohibited. |
|
Cleaning Method |
Flush Spill Area with Water andremove with liquid-absorbing material like foam sand,sawdust etc.. |
|
Handling |
The usual precautions for handling chemicals should be observed See Section 8 Eyewash bottles should be available. |
|
Storage |
Keep only in the original container in a cool, well ventilated place (S3/9/49) Protect from frost. |
| Condition to Avoid | Non flammable but avoid direct heating |
| Materials to Avoid | Do not subject to Acidic / Oxidizing Agents. |
| Handling | Keep Container Tightly Closed |
NOTE : Eyewash facilities require atworkplace The product causes corrosion on skin and mucous membranes Pl. Note that In case of discharge of acidic or alkaline products into the sewerage system the pH must be in the range of 6-10 since higher or lower pH values may damage the sewerage system or impair biological dosage treatment plants. So that for maintaining pH we have to add acidic / basic medium neutaliser . For example if pH is less than 6 basic neutraliser is required and if pH is more than 10 acidic nature neutraliser is required. For details of any guideline pl. Visit our technical website www.rxmarine.com
- Dilute in water (always use plastic jar and RXSOL should be added to water never add water to RXSOL.)
|
Exposure Limits |
There are no recommended or established controls for this product |
|
Exposure controls |
No special ventilation is required unless the product is used in a spray form |
|
Occupational exposure controls |
Wear suitable protective clothing, including eye/face protection and gloves (plastic or rubber are recommended) During fumigation/spraying wear suitable respiratory equipment (S42) |
|
Personal protection |
|
|
Respiratory System Protection |
Approved respirator must be worn when spraying |
|
Eye Protection |
wear eye protection (on possibility of contact ) |
|
Hand protection |
wear PVC chemical resistance protective glove |
PRODUCT PROPERTIES:
|
Appearance |
Clear Liquid |
|
Density |
In g/cm3 at 20°C: 1.01 |
|
Compatibility |
|
|
Metal |
No known effect |
|
Rubber |
No known effect |
|
pH |
4.5 to 7.5 |
|
Solubility |
100% soluble in water |
|
Packaging |
210 Size (in Litres), Also Available in 25 Ltr |
- Stable
- Avoid overheating, Keep away from frost
- See Section 5
- Hazardous Decomposition Products:
Do not occur if stored and used as directed. In FIRE combustion CO, CO2 , NH3, SOXetc hazardous gas produced.
NOTE : AVOID CONTACT WITH ACID
|
Toxicological information |
No experimental data available. |
|
Inhalation |
Vapours or aerosols may cause irritation of eyes, nose and respiratory tract. |
|
Contact with skin |
Prolonged skin or eye contact may cause chemical burns. |
|
Contact with eyes |
Prolonged skin or eye contact may cause chemical burns. |
|
Ingestion |
The ingestion of significant quantities may cause burning sensation. |
|
Carcinogenicity |
No evidence of carcinogenic effects. |
|
Inhalation |
Vapours or aerosols may cause irritation of eyes, nose and respiratory tract. |
|
LD50 (oral) |
> 2000 mg/kg - (Polyvinyl alcohol, partly saponified). |
No components of this material are toxic to aquatic organisms, product are readily biodegradableas by mixing with water.
|
Disposal considerations |
Non hazardous. Disposal should be in accordance with local, state or national legislation. |
Transport over land ADR/RID : Not classified as hazardous for transport
|
Classification and labelling |
Not classified as hazardous for users- S2 : Keep out of reach of children S26 : Incase of contact with eyes, rinse immediately with plenty of water and seek medical advice. S28 : After contact with skin, wash immediately with plenty of water. S37/39 : Wear suitable gloves and eye/face protection. |
This information is based on our current level of knowledge and relates to the product in the state in which it is delivered. It is intended to describe our products from the point of view of safety requirements and is not intended to guarantee any particular properties Text of R and S phrase codes used in this safety data sheet
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.