Where to use Safe Passivator Liquid 630?
Safe Passivator Liquid 630 is recommended for:
Passivation after pickling: Applied to freshly pickled stainless-steel surfaces to promote restoration of the protective passive layer.
Passivation after mechanical treatment: Suitable after grinding, brushing, polishing, blasting and fabrication operations that may disturb the stainless-steel passive surface.
Free iron / smut removal: Helps remove traces of free iron and surface residues that may otherwise cause rust spots or discoloration.
Flash rust prevention: Particularly useful immediately after pickling where flash rust or brown staining may occur during drying.
Post-pickling treatment: Can be used as a final conditioning treatment before equipment is returned to service.
How to make safety as a priority while using Passivation Liquids - Use RXSOL Safe Passivator Liquid 630!
| Step | Procedure |
|---|---|
| 1. Surface Preparation | Ensure the stainless-steel surface is free from heavy grease, oil and loose contamination. Where required, pre-clean with a suitable alkaline or neutral degreaser. |
| 2. After Pickling | Thoroughly rinse away the pickling chemical with clean water before applying Safe Passivator Liquid 630. |
| 3. Application | Apply uniformly by low-pressure spray, brush, immersion or circulation depending upon the equipment and surface geometry. |
| 4. Contact Time | Allow approximately 10-15 minutes contact time under normal conditions. Do not allow the product to dry completely on the surface. |
| 5. Final Rinsing | Rinse thoroughly with clean fresh water. High-pressure rinsing may be used where appropriate. |
| 6. Drying | Allow the treated stainless-steel surface to drain and dry naturally or use clean, oil-free compressed air where required. |
Treatment of Flash Rust / Smut
Where smut or light flash rust appears immediately after pickling, apply Safe Passivator Liquid 630 while the stainless-steel surface is still wet.
Allow approximately 10-15 minutes reaction time and then rinse thoroughly with clean water.
For heavier contamination, pre-clean the affected surface, rinse with water and then apply Safe Passivator Liquid 630 to the clean, wet surface.
Reduction of Nitric Fumes During Pickling
Where nitric-acid-containing pickling products are being used, Safe Passivator Liquid 630 may be applied as a fine mist over the wet treated surface as part of the post-pickling procedure to help suppress residual fuming.
This application should not be considered a substitute for proper ventilation, extraction or required PPE.
| Property | Typical Value |
|---|---|
| Appearance | Clear liquid |
| Product Type | Stainless-steel passivating / conditioning liquid |
| Acid Content | Acid-free |
| Nitric Acid | None |
| Solubility in Water | Completely miscible |
| Application | Spray / Brush / Immersion / Circulation |
| Typical Contact Time | 10-15 minutes |
| Rinsing | Fresh water |
| Main Function | Passivation and removal/control of free iron contamination |
Why is RXSOL Safe Passivator Liquid 630 better than industry standard acidic passivation liquids?
- Acid-free passivating treatment for stainless steel
- Helps restore the passive surface layer after pickling
- Suitable for use after welding, grinding, brushing and blasting
- Helps remove residual free iron and smut
- Reduces the possibility of flash rust and surface staining
- Improves the final appearance after pickling
- Helps minimize discoloration associated with residual surface contamination
- Can help reduce nitric fumes where used as a post-treatment during nitric-acid-containing pickling operations
- Produces no strongly acidic passivation waste
- Simple spray, brush or circulation application
- Suitable for general industrial and marine stainless-steel maintenance
- Chemical-resistant low-pressure spray equipment
- Acid/chemical-resistant pumps
- Plastic or compatible stainless-steel application equipment
- Brushes and suitable manual application systems
- Immersion tanks
- Circulation cleaning systems
| Product Name | Safe Passivator Liquid 630 |
| Product Part Number | RXSOL-38-1630-025 |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Stock Point : Mumbai, Gandhidham, Vizag, Chennai, Kolkata, Fujairah, Muscat, Nairobi Kenya, Canada
| Phone | +91 22 27815540 / 41 / 42 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| mail@rxmarine.com |
Proprietory blend of non-hazardous, acid-free solutions.
The product does not meet the criteria for classification in any hazard class according to Regulation (EC) No 1272/2008 on classification, labelling and packaging of substances and mixtures.
3.1 Label elements
Labelling according to Regulation (EC) No 1272/2008: Void
Hazard pictograms: Void
Signal word: Void
Hazard statements: Void
Precautionary statements:
P261 – Avoid breathing spray.
P280 – Wear protective gloves / eye protection.
P305+P351+P338 – IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P405 – Store locked up.
P410+P412 – Protect from sunlight. Do not expose to temperatures exceeding 50°C/122°F.
P501 – Dispose of contents/container in accordance with local/regional/national/international regulations.
Additional information:
Read Safety Data Sheet before use.
3.2 Other hazards
Results of PBT and vPvB assessment
PBT: Not applicable.
|
Eye Contact: |
Check for and remove any contact lenses. In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Cold water may be used. Get medical attention immediately. |
|
Skin Contact: |
In case of contact, immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Cover the irritated skin with an emollient. Cold water may be used.Wash clothing before reuse. Thoroughly clean shoes before reuse. Get medical attention immediately |
|
Serious Skin Contact: |
Wash with a disinfectant soap and cover the contaminated skin with an anti-bacterial cream. Seek immediate medical attention. |
|
Inhalation: |
If inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention immediately. |
|
Serious Inhalation: |
Evacuate the victim to a safe area as soon as possible. Loosen tight clothing such as a collar, tie, belt or waistband. If breathing is difficult, administer oxygen. If the victim is not breathing, perform mouth-to-mouth resuscitation. WARNING: It may be hazardous to the person providing aid to give mouth-to-mouth resuscitation when the inhaled material is toxic, infectious or corrosive. Seek immediate medical attention |
|
Ingestion: |
Do NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Loosen tight clothing such as a collar, tie, belt or waistband. Get medical attention if symptoms appear |
|
Serious Ingestion: |
Not available. |
|
Flammability of the Product: |
Non-flammable. |
|
Auto-Ignition Temperature: |
Not applicable. |
|
Flash Points: |
Not applicable. |
|
Flammable Limits: |
Not applicable |
|
Products of Combustion: |
Not available. |
|
Fire Hazards in Presence of Various Substances: |
combustible materials |
| Explosion Hazards in Presence of Various Substances: | Slightly explosive in presence of open flames and sparks, of heat, of organic materials, of metals, of acids. |
6.1 Personal precautions, protective equipment and emergency procedures Ensure adequate ventilation Use respiratory protective device against the effects of fumes/dust/aerosol.
6.2 Environmental precautions: Not applicable Do not allow to enter sewers/ surface or ground water.
6.3 Methods and material for containment and cleaning up: Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). Dispose contaminated material as waste according to item 13. Ensure adequate ventilation.
6.4 Reference to other sections See Section 7 for information on safe handling. See Section 8 for information on personal protection equipment. See Section 13 for disposal information
|
Precautions: |
Keep locked up. Keep container dry. Keep away from heat. Keep away from sources of ignition. Keep away from combustible material.. Do not ingest. Do not breathe gas/fumes/ vapor/spray. Never add water to this product. In case of insufficient ventilation, wear suitable respiratory equipment. If ingested, seek medical advice immediately and show the container or the label. Avoid contact with skin and eyes. Keep away from incompatibles such as oxidizing agents, reducing agents, combustible materials, organic materials, metals, acids, alkalis |
|
Storage: |
Keep container tightly closed. Keep container in a cool, well-ventilated area. Separate from acids, alkalies, reducing agents and combustibles. See NFPA 43A, Code for the Storage of Liquid and Solid Oxidizers. Do not store above 8°C (46.4°F). Refrigerate Sensitive to light. Store in light-resistant containers. |
8.1 Control parameters · Ingredients with limit values that require monitoring at the workplace: The product does not contain any relevant quantities of materials with critical values that have to be monitored at the workplace. · Additional information: The lists valid during the making were used as basis.
8.2 Exposure controls · Individual protection measures, such as personal protective equipment · General protective and hygienic measures: The usual precautionary measures are to be adhered to when handling chemicals. Wash hands before breaks and at the end of work. Do not inhale gases / fumes / aerosols. · Respiratory protection: Not necessary if room is well-ventilated
|
Physical state and appearance: |
Liquid |
|
Odor |
Odorless. |
|
Taste |
Bitter |
|
Molecular Weight: |
Not applicable. |
|
Color: |
Clear Colorless |
|
pH (1% soln/water): |
Not available |
|
Boiling Point: |
100°C or 212°F |
|
Critical Temperature |
Not available |
|
Specific Gravity |
1 |
|
Vapor Pressure |
3.1 kPa (@ 20°C) |
|
pH |
6-7 |
|
Odor Threshold |
Not available |
|
Water/Oil Dist. Coeff. |
Not available |
|
Ionicity (in Water) |
Not available |
|
Dispersion Properties |
See solubility in water, diethyl ether |
|
Solubility |
Easily soluble in cold water. Soluble in diethyl ether |
|
Stability |
The product is stable. It contains a stabilizer |
|
Instability Temperature: |
Not available |
|
Conditions of Instability |
Excess heat, incompatible materials |
|
Incompatibility with various substances |
Reactive with reducing agents, combustible materials, organic materials, metals, acids, alkalis. |
|
Corrosivity: |
Non-corrosive in presence of glass |
Special Remarks on Corrosivity: Not available.
Polymerization: Will not occur.
11.1 Information on hazard classes as defined in Regulation (EC) No 1272/2008
Acute toxicity Based on available data, the classification criteria are not met.
Skin corrosion/irritation Based on available data, the classification criteria are not met.
Serious eye damage/irritation Based on available data, the classification criteria are not met.
Respiratory or skin sensitisation Based on available data, the classification criteria are not met.
Germ cell mutagenicity Based on available data, the classification criteria are not met.
Carcinogenicity Based on available data, the classification criteria are not met.
Reproductive toxicity Based on available data, the classification criteria are not met.
STOT-single exposure Based on available data, the classification criteria are not met.
STOT-repeated exposure Based on available data, the classification criteria are not met.
Aspiration hazard Based on available data, the classification criteria are not met. ingestion may affect metabolism (weight loss). Prolonged or repeated inhalation may affect respiration, blood.
12.1 Toxicity
Aquatic toxicity: No further relevant information available.
12.2 Persistence and degradability No further relevant information available.
12.3 Bioaccumulative potential No further relevant information available.
12.4 Mobility in soil No further relevant information available.
12.5 Results of PBT and vPvB assessment · PBT: Not applicable. · vPvB: Not applicable.
12.6 Endocrine disrupting properties The product does not contain substances with endocrine disrupting properties.
12.7 Other adverse effects · Additional ecological information: · General notes: Water hazard class 2 (German Regulation) (Self-assessment): hazardous for water Do not allow product to reach ground water, water course or sewage system. Danger to drinking water if even small quantities leak into the ground.
|
Waste Disposal: |
Waste must be disposed of in accordance with federal, state and local environmental control regulations. |
- Not classified as hazardous for transport
The information provided about the product on this Safety Data Sheet has been compiled from knowledge of the individual constituents The data given here is based on current knowledge and experience. This Safety Data Sheet describes the product in terms of safety requirements and does not signify any warranty with regard to the product's properties The data given here only applies when product used for proper application(s).
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.