A powerful penetrating mixed chemical products to remove heavy SLAGS, Rock Phospate deposits, LIME deposits. Additionally, it may also be used to remove mineral deposits and eliminate bad odors in tanks and other closed systems. Also Can be used as a COAL REMOVER.
It is free from hydrocarbon solvents, non flammable and biodegradable.
Biodegradable / Non-Toxic / Non-Pollutant.
VERY Cost effective.
Recommended to use spray equipment.
The use of hot water will greatly enhance the effectiveness of the cleaning and should be utilized whenever possible.
• Use cold - no heating required.
• Easily dissolves deposits containing carbon , polymer resin etc.
• Economical to use.
• Scraping not required.
• Non- flammable.
• Helpful for burner tips, fuel injectors and all components fouled by carbon, resin or varnishes.
• Cleans oil side of fuel heaters, oil coolers, etc.
• Can be used for cleaning of : -Fuel Oil Filters - Pistons - Piston rings - Valve cage
Directions for Use and Dose Rates
Soak Method:-
It may be used concentrated or diluted with water, depending on the degree of contamination, the surface area to be treated, the desired degree of cleaning and the available downtime.Actually, the user is the best one capable to regulate the quantity and concentration to be used for the situation at hand.In any case, when the accumulation is not heavy, a 50% solution with water must be used. Otherwise,RXSOL-22-2201-210. can be used undiluted especially when deposition is heavy and hard spots persist.
Cleaning Procedure
Conventional cleaning methods such as a brush,hard sponge, thick and hard broom and /or a mop can be used on heavy duty and hard stain deposits.Note that for heavy accumulations the cleaning procedure might be necessary to be repeated until the results are satisfactory. Furthermore, is important to keep in mind that 1 litre of RXSOL-22-2201-210 is sufficient to cover a surface area of 8–10 square meters.
NOTE ::: -- Let this product soak into the surface for 30-45 minutes. Then using a high-powered spray washer blast the surfaces until the stains and discoloration is gone.
Note:-
• Cleaning time will vary depending on the extract nature and thickness of deposit to be removal.
• Stubborn deposits should be scrubbed to assist the cleaning operation.
Your local Rx CLEANSERS representative will work with you to design the optimum concentration & procedure for your system.
RXSOL-22-2201-210 should be mixed with fresh water to form a solution of 10-30%, depending on the extent of scaling. After using RXSOL-22-2201-210 it is essential to thoroughly rinse all metal surfaces at least once with a 0.5% solution of Alkalinity Control in fresh water. This solution should be circulated for 2-4 hours or until an acceptable pH value is obtained. This will neutralize any remaining acidity & passivate steel surfaces.
**Read the Material Safety Data Sheet before using this product.**
Other Valuable Hold Cleaners :::
Cement Remover RX Hold ::: Highly concentrated and powerful penetrating agents materials which is effectively react with cement to loosen the bonding strength . Best results can obtain on dry surface of cement. RXSOL'S R & D has developed this molecular cement dissolver. Part No.- RXSOL-22-2202-025, Part No.- RXSOL-22-2202-020, Part No.- RXSOL-22-2202-050
Safety And Handling :-
“RXSOL-22-2201-210” is completely safe to handle, being non-toxic & non corrosive.As with all chemicals general safety and handling procedures apply. Avoid contact with eyes as irritation may occur. Do not take internally. In case of contact with eyes, flush eyes immediately and cupiously with clean running water for 15- minutes and seek medical attention.
| Product Name | : | Rock Phospate Cleaner RX HOLD |
| Product Type | : | Cargo Hold and Tank Cleaner |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | : | +91 22 65113333 / 5555 / 9999 / 27611360 |
| Fax | : | +91 22 2781 1318 :::AOH :0091 9821214367 |
| : | mail@rxmarine.com/ |
| Chemical Name | CAS # | % BY WEIGHT |
| NaOCl | 7681-52-9 | 40-50 |
| Surfactant | NA | 60-40 |
| Eye | Can cause permanent eye injury. Symptoms include stinging, tearing, redness, and swelling of eyes. Can injure the cornea and cause blindness. |
| Skin |
Can cause permanent skin damage. Symptoms may include redness, burning, and swelling of skin, burns, and other skin damage. Additional symptoms of skin contact may include: skin blistering, hair loss, Passage of this material into the body through the skin is possible, but it is unlikely that this would result in harmful effects during safe handling and use. |
| Swallowing |
Swallowing this material may be harmful or fatal. Symptoms may include severe stomach and intestinal irritation (nausea, vomiting, diarrhea), abdominal pain, and vomiting of blood. Swallowing this material may cause burns and destroy tissue in the mouth, throat, and digestive tract. Low blood pressure and shock may occur as a result of severe tissue injury. |
| Inhalation | It is possible to breathe this material under certain conditions of handling and use (for example, during heating, spraying, or stirring). Breathing this material may be harmful or fatal. Symptoms may include severe irritation and burns to the nose, throat, and respiratory tract. |
| Target Organ Effects | This material (or a component) has been shown to lower activity of certain immune system cells in experimental animals. The significance of this effect with respect to human health is uncertain. |
| Developmental Information | There are no data available for assessing risk to the fetus from maternal exposure to this material. |
| Primary Route(s) of Entry |
Inhalation, Skin contact, Eye contact. |
| Eyes |
If material gets into the eyes, immediately flush eyes gently with water for at least 15 minutes while holding eyelids apart. If symptoms develop as a result of vapor exposure, immediately move individual away from exposure and into fresh air before flushing as recommended above. Seek immediate medical attention. |
| Skin | Immediately flush skin with water for at least 15 minutes while removing contaminated clothing and shoes. Seek immediate medical attention. Wash clothing before reuse and discard contaminated shoes. |
| Swallowing | Seek immediate medical attention. Do not induce vomiting. Vomiting will cause further damage to the mouth and throat. If individual is conscious and alert, immediately rinse mouth with water and give milk or water to drink. If possible, do not leave individual unattended. |
| Inhalation | If symptoms develop, immediately move individual away from exposure and into fresh air. Seek immediate medical attention; keep person warm and quiet. If person is not breathing, begin artificial respiration. If breathing is difficult, administer oxygen. |
| Note to Physicians | Preexisting disorders of the following organs (or organ systems) may be aggravated by exposure to this material: skin, lung (for example, asthma-like conditions), immune system. |
| Flash Point | Not applicable |
| Explosive Limit | Not applicable |
| Autoignition Temperature | No data |
| Hazardous Products of Combustion | NA |
| Fire and Explosion Hazards | No special fire hazards are known to be associated with this product. |
| Extinguishing Media | Use an extinguishing media appropriate for surrounding fire.. |
| Fire Fighting Instructions |
Water may be used to keep fire-exposed containers cool until fire is out. Wear a self-contained breathing apparatus with a full facepiece operated in the positive pressure demand mode with appropriate turn-out gear and chemical resistant personal protective equipment. Refer to the personal protective equipment section of this MSDS. |
| Small Spill | Dilute with water and absorb onto a noncombustible absorbent material. |
| Large Spill | Prevent run-off to sewers, streams or other bodies of water. If run-off occurs, notify proper authorities as required, that a spill has occurred. Collect and add slowly to large volume of water. Persons not wearing protective equipment should be excluded from area of spill until clean-up is completed. Stop spill at source. Dike to prevent spreading. Pump to salvage tank. |
| Handling |
Containers of this material may be hazardous when emptied. Since emptied containers retain product residues (vapor, liquid, and/or solid), all hazard precautions given in the data sheet must be observed. Emergency eyewash fountains and safety showers should be available in the immediate vicinity of potential exposure |
| Eye Protection | Chemical splash goggles and face shield (8" min.) in compliance with OSHA regulations are advised; however, OSHA regulations also permit other type safety glasses. (Consult your industrial hygienist.) |
| Skin Protection | Wear impervious gloves (consult your safety equipment supplier). To prevent skin contact, wear impervious clothing and boots.. |
| Respiratory Protections | If overexposure has been determined or documented, a NIOSH/MSHA jointly approved air supplied respirator is advised in absence of proper environmental control. OSHA regulations also permit other NIOSH/MSHA respirators under specified conditions. (See your safety equipment supplier.) Engineering or administrative controls should be implemented to reduce exposure. |
| Engineering Controls | Provide sufficient mechanical (general and/or local exhaust) ventilation to maintain exposure below level of overexposure (from known, suspected or apparent adverse effects). |
| Exposure Guidelines | Component |
| Boiling Point | (for component) 212.0 F (100.0 C) | |
| Vapor Pressure | (for component) 17.500 mmHg | |
| Specific Vapor Density | No data | |
| Specific Gravity | 1.220 - 1.250 @ 68.00 F | |
| Liquid Density |
10.400 lbs/gal @ 68.00 F 1.250 kg/l @ 20.00 C |
|
| Percent Volatiles | 87.5% | |
| Evaporation Rate | SLOWER THAN ETHYL ETHER | |
| Appearance | No data | |
| State | LIQUID | |
| Physical Form | HOMOGENEOUS SOLUTION | |
| Color | CLEAR TO YELLOW LIQUID | |
| Odor | CHLORINATED | |
| pH | 11.5-12.50 | |
| Solubility in Water | SOLUBLE |
| Hazardous Polymerization | Product will not undergo hazardous polymerization. |
No data
No data
| Waste Management Information | Dispose of in accordance with all applicable local, state and federal regulations. |
| DOT Information | 49 CFR 172.101 | |
| DOT Description: | Mixture HYPOCHLORITE SOLUTIONS,8,UN1791,III | |
| Container/Mode: | 55 GAL DRUM/TRUCK PACKAGE | |
| NOS Component: | Not applicable | |
| RQ (Reportable Quantity) | - 49 CFR 172.101 | |
| Product Quantity (lbs) | Component |
Chemical Weapons Convention: No TSCA 12(b): No CDTA: No
SARA 311/312: Acute: Yes Chronic: No Fire: No Pressure: No
Reactivity: No (Mixture / Liquid)
Australian Hazchem Code: None allocated.
Poison Schedule: S5
This MSDS has been prepared according to the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all of the information required by the CPR
The information accumulated herein is believed to be accurate but is not warranted to be whether originating with the company or not. Recipients are advised to confirm in advance of need that the information is current, applicable, and suitable to their circumstances.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.