Membrane ALKA Clean RXSOL ORG-10 is a high pH formultion that has been designed specifically to remove organics, silt and other particulate deposits from all polyamide, polysulfone and thin film composite membrane surfaces.
Membrane ALKA Clean RXSOL ORG-10 is a powdered buffered alkaline detergent developed, Especially for cleaning alkaline tolerant reverse osmosis and ultrafiltration membranes.
High-performance alkaline cleaning agent designed for use in Reverse Osmosis (RO) and Nano-Filtration (NF) membrane systems. It is especially effective against a wide range of organic foulants, biofilm, and aluminium silicate scale — one of the most difficult-to-remove deposits in membrane systems.
This formulation combines powerful dispersants, chelating agents, and surfactants in a synergistic blend that penetrates and solubilizes stubborn deposits without harming membrane integrity when used as recommended.
Inspect cleaning tank, hoses and cartridge filter. Install new filter elements.
Fill cleaning tank with RO solution then, Slowly add 25 grammes of ORG 10 for each litre of cleaning tank capacity. Thoroughly mix cleaning solution by using a mixer or by circulating it through the cleaning pump. The solution may be heated to improve cleaning effectiveness.
Do not exceed the membrane manufacturer’s temperature limits.
Circulate the solution through the membrane bank in the feed direction for one hour at the flow rate recommended by the membrane or system manufacturer. If the manufacturer’s recommendations are not available, the following guidelines may be used.
Maintains production capacity
Special formula maintains membrane flux rate
Chelates and buffered alkalinity effectively remove fouling agents from alkaline
Tolerant RO and UF membranes
BENEFIT :::
Dissolves freely to reduce labor and cleaning time, Easy to add balance formulation eliminates need for adding separate additives or boosters, Rinse quickly and completely to reduce cleaning time
ITS ADVANCE FORMULATION Makes Economical use cost and recommended use dilution, Chlorine free formulation helps assure compatibility with membrane to Extent membrane life.
Key Areas of Application of Membrane ALKA Clean RXSOL ORG Membrane Cleaner
- Reverse Osmosis (RO) Membrane Systems
- Nano-Filtration (NF) Systems
- Ultra-Filtration Pre-Cleaning (as compatible)
- Desalination Plants, Water Recycling, and Process Water Systems
Spiral wound membrane
|
Membrane diameter |
Flow rate per tube (parallel flow) |
| 4 | 23 (6) |
| 6 | 53 (14) |
| 8 | 91 (24) |
| 10 | 114 (38) |
| 12 | 204 (54) |
Hollow fibre membrane
|
Membrane diameter |
Flow rate per element (parallel flow) |
| 4 | 19 (6) |
| 8 | 57 (24) |
| 10 | 76 (38) |
TO USE
For normal CIP cleaning or soak cleaning RO and UF system completely , Pre dissolve in warm water before adding to system. Typically used Concentration is 0.7 to 1.5 % or 9-20 ounces of RXSOL ORG 10 per each 10 Gallon (67-150 grams/10 l) f water. Circulate throughout the system for 20 Minutes at a temperature of 120-160 degree F (49 – 71 degree C)
Note:
Observe the recommendation of the manufacturer of the membrane for Maximum temperature.
This advanced, high s trength powder has the following features:
- pH adjusted to 10+ 0.5
- Highly effective at ambient temperatures
- Contains no surfactants and is quickly rinsed away
- Contains detergent builders, chelating agents and pH buffer
RXSOL ORG-10 is suitable for use with all polyamide, polysulfone and thin film, composite membranes. It can be used at temperatures from 15°C (60°F) up to the maximum recommended by the membrane manufacturer.
The standard dilution ratio is 25 grammes of ORG 10 per litre of water.
PROPERTIES
Form ………………..........Powder Alkalinity
Color……………………... White
Active as Na2O……………… 16.2%
Foam …………...……….. High
Total as Na2O ………… 19.8 %
PH of 1% solution ……. 10 to 12
BULK DENSITY - 0.95 -
FREEZING POINT: NOT APPLICABLE
| Parameter | Value |
|---|---|
| Appearance | White to Off-white Powder |
| Solubility in Water | Completely soluble |
| pH (1% Solution) | 10 – 12 |
| Specific Gravity | Not applicable (powder form) |
| Foaming Nature | Moderate to High |
In cases of heavy fouling, the first return flow (up to 15% of the cleaning tank volume) should be diverted to drain to prevent redeposition of removed solids.
In multi-pass systems, best results will be achieved if each pass is cleaned separately.
The solution should be discarded if it becomes turbid or discoloured by removed material.
A fresh solution should then be prepared before cleaning additional passes.
Rinse with permeate before returning the system to service.
Features of Membrane ALKA Clean RXSOL ORG-10 for effective RO Membrane Cleaning
- Suitable for use in Reverse Osmosis (RO) and NanoFiltration (NF) membranes
- Removes most organic and inorganic deposits
- Cost effective powdered product
- Compatible with all polyamide membranes
- Removes aluminium silicate
- Excellent for alkaline prewash
Advantages of Membrane Alka Clean RO Membrane Cleaner
- Highly effective against aluminium silicate, biofilm, and organic fouling
- Foaming formulation enhances cleaning contact and effectiveness
- Suitable for use in most polyamide and composite membranes (check pH compatibility)
- Contains strong chelating agents to dissolve metal ion-bound foulants
- Compatible with warm water to boost cleaning power
- Helps restore membrane performance and reduce differential pressure
RXSOL ORG 10 is also suitable for meat and poultry plant as a cleaner for reverse Osmosis and Ultra filtration membranes. RXSOL ORG 10 must be used in a manner which prevents direct or indirect contamination of edible.
| Product Name | RXSOL-33-3320-025 |
| Product Type | Membrane Cleaner for Organics and Particulates |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Stock Point : Mumbai, Gandhidham, Surat, Chennai, Visakhapatnam, Fujairah, Barka Muscat, Kolkata
| Phone | +91 22 27815541 / 42 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| mail@rxmarine.com |
| Name of the chemical | EC No. | CAS-No | % |
| citric acid | 201-069-1 | 77-92-9 | 5-10% |
| sodium Hydroxide | 1310-73-2 | 10-18% | |
| sodium tripolyphosphate ( Tri phosphonic Acid, pentasodium salt ) | 231-838-7 | 7758-29-4 | 30-60% |
| Tetrasodium edta ( Acetic Acid Ethylenedinitrilo tetra, tetrasodium salt ) | 200-573-9 | 64-02-8 | 30-60% |
| Trisodium phosphate | 231-509-8 | 7601-54-9 | 30-60% |
| Sodium Dodecylbenzene Sulfonate | 25155-30-0 | 4-5% |
Formula contains not more than 2.8% phosphorus, 1.17gms per gal average recommended use concentration
| skin contact | Irritant |
| eye contact | Irritant |
| inhalation |
Privide fresh air, warmth and rest , preferably in a comfortable upright sitting position. Get medical attention if any discomfort continues. |
| ingestion |
DO NOT INDUCE VOMITING. Rinse mouth thoroughly. Get medical attention. |
|
Inhalation |
Provide fresh air, warmth and rest , preferably in a comfortable upright sitting position. Get medical attention if any discomfort continues. |
| Ingestion |
DO NOT INDUCE VOMITING. Rinse mouth thoroughly. Get medical attention. |
| Skin Contact | Immediately remove contaminated clothing. Rinse immediately with plenty of water. Continue to rinse for at least 15 minutes. Get medical attention if irritation persists after washing. |
| Eye Contact | Rinse the eye with water immediately. Continue to rinse for at least 15 minutes. Contact physician if irritation persists. |
|
ESTINGUISHING MEDIA |
Use: Water spray, for or mist. Foam, carbon dioxide or dry powder. |
| PROTECTIVE MEASURES IN FIRE |
Use self-contained breathing apparatus |
| Spill Clean Up Methods | Collect and reclaim or dispose in sealed containers in lincensed waste. Containers with collected spillage must be properly labelled with correct contents and hazard symbol. Should be prevented from entering drains. |
| Usage Precautions | Avoid Spilling, skin and eye contact. Avoid handling which leads to dust formation. Static electricity and formation of sparks must be prevented. |
| Storage Precautions |
Store in tightly closed original container in a cool, dry well- ventilated place. Store separated from: Alkalies. Oxidising material. Aluminium |
|
Ingredients Comments |
No exposure limits noted for ingredients (s). |
| Engineering Measures | Provide sufficient ventilation for operations causing dust formation. |
|
|
Wear respiratory if there is dust formation. |
|
Hand Protection |
Selection of a suitable glove depends on work conditions and whether the products is present on its own or in combination with other substances. Breakthrough time is dependent on the characteristics of the brand of glove used, consult your supplier. It has been found that gloves made from rubber, neoprene or PVC provide short-term splash protection. |
| Eye Protaction | Wear approved safety goggles |
| Other Protection | Wear appropriate clothing to prevent repeated or prolonged skin contact. |
| Hygiene Measures | No specific hygiene procedures noted , but goog personal hygiene practices are alwayes advisable, especially when working with chemical |
|
Appearance |
Powder, Dust |
| Colour | White |
|
odour |
Slight Odour |
| Solubility | Soluble in water |
| melting Point (c) | >150 |
| pH - Value, Diluted Solution | 9.5-10.5 |
| Relative Density | 1.67 |
| Conditions to Avoid | Avoid dust close to iginition sources. Avoid contact with: Strong oxidising agents. Strong alkalis. Aliminium in contact with metals genrates hydrogen gas, which together with air can from explosive mixtures. |
| Hazardous Decompostion Products |
Toxic gases/vapoursfumes of: carbon dioxide (CO2). Carbon monoxide (CO). Aqueous solutions in contact with aluminium may produce hydrogen |
| Inhalation | Irritating to respiratory system |
| Skin Contact |
Causes bums. Not a skin Sensitiser |
| Eye Contact | Irritating to eyes |
N/A
| Disposal Methods | Absorb in vermiculite or dry sand, dispose in licensed special waste |
| Rail Transport Notes | N/A |
| Sea Transport Notes |
N/A |
| Air Transport Notes | N/A |
| ADR Class | Not Classified for transportation |
| Marine Pollutant | No. |
| Labelling | Corrosive |
| Contains |
Trisodium Phosphate |
| Risk Phrases | |
| R34 | Causes Bums |
| R37 | Irritating to respiratory system |
| Safety Phrases | |
| S45 | In case of accident or if you feel unwell, seek medical advice immediately (show label where possible) |
| S24/25 | Avoid conwith skin and eyes |
| S36/37/39 | Wear suitable protective clothing. gloves and eye/face protection |
| S26 | In case of cantact with eyes, rinse immediately with plenty of water and seek medical advice. |
| S27 | Take off immediately all contaminated clothing |
The information accumulated herein is believed to be accurate but is not warranted to be whether originating with the company or not. Recipients are advised to confirm in advance of need that the information is current, applicable, and suitable to their circumstances. This MSDS has been prepared by Rx Marine International.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.