Fast and effective scale remover which removes scale and rust from condensers, evaporators, heat exchangers,Rediator, boilers etc. RXSOL-16-1008-210 , Descaling Liquid is a liquid mixture of descaling accelerators, corrosion-inhibitors and wetting agents.
Uniqueness of 1008 :: --
RXSOL 1008 Descaler has the ability to dissolve approximately 1.5kg of calcium carbonate scale per gallon in concentrated form. It does not need to be heated up during cleaning. The uniqueness of this Descaler allows you to clean some equipment while still in operation utilizing a minimum of your own personnel.
Features, Benefits and Applications
- Scale dissolver product contains inhibitors against attack on ferrous metals.
- Unlimited shelf life.
- Easy to rinse off.
- Fast and effective scale remover.
- Removes scale and rust from condensers, evaporators, heat exchangers,Rediator etc.
Removes water scale from boilers.
RXSOL brand descaler is one of POPULAR brand in INDIA and Middle East. We are One of Largest Descaler manufacturer, Exporter and supplier.
The most effective RXSOL-16-1008-210, Descaling Liquid is accomplished by circulation for large systems or components. In the case of small components, the soak method in an immersion bath can be used.
If the equipment to be cleaned is contaminated by oil, grease, sludge or carbonised oil, then pre-cleaning with RXSOL-20-2002-025 ( www.rxmarine.com/seacleaner-25-ltr ) is necessary.
RXSOL-16-1008-210 should alway be used in plastic bucket. RXSOL-16-1008-210 should always be added in , never add water in RXSOL-16-1008-210.
RXSOL-16-1008-210 dilute with fresh water as 5-30%, solution depending on scale.
After using RXSOL-16-1008-210 rinse all metal surfaces at least one time with a 0.5% solution of RXSOL-20-2005-025 ( www.rxmarine.com/alkaleen-liquid-heavy-duty-25-ltr ) in fresh water. This solution should be circulated for 2-4 hours or until pH value comes 6-7. This will neutralize any remaining acid and passivate steel surfaces.
• Automotive - Closed Circuit Cooling, Dynamometers, Extruders, Molders, Radiators, Welders
• Bottling - CO2 Generators, Heaters, Exchangers, Rinse Tanks, Sterilizers, Washers
. HOUSE HOLD - Dissolves hard and old lime scale deposits from your appliances. It extends the life of the appliance and saves running cost. It can be used in appliances such as Washing Machines, Dish Washers, Geysers, Steam Iron, Coffee Makers, Bath Tubs, Bathroom Fixtures etc.
• Buildings - Chillers, Cooling Towers, Pipework
• Chemicals - Dryers, Extruders, Kettles, Mixers, Reactors, Scrubbers, Vacuum Pumps
• Food - Condensers, Ice Machines, Kathabars, Refrigeration Equipment, Steam Tables
• Manufacturing - Chillers, Compressors, Furnaces, Quenchers, Vacuum Pumps
• Metals - Bearings, Castings, Fans, Hearth & Vacuum Furnaces, Shelters, Sprays
• Mining - Bearings, Conveyors, Filters, Presses, Process Lines, Radiators
• Paper- Calendar Mill Rolls, Caustic Lines, Scrubbers, Compressors, Liquor Tanks, Pulverizers, Vacuum Pumps
• Pharmaceutical- Exchangers, Loop Systems, Kathabars, Pumps, Reactors, Stills, Sterilizers
• Refinery - Compressors, Converters, Crackers, Exchangers, Piping, Pumps
• Rubber/Plastics - Banbury Mixers, Calendar & Mill Rolls, Extruders, Injection Molders, Molds, Temperature Control Units, Throat Coolers, Towers, Tubers
• Steel - Bearings, ConCast Units, Generators, Hearths, Spangle Units, Furnaces
• Textile - Air Washers,Compressors, Condensers, Exchangers, Extruders,Towers
Boilers
Condensers
Filters
Heat Exchangers
Kettles & Tanks
Pipelines
Pots
Reactors
Steam Jackets
Bath Rooms and Showers
Metal Processing and much more!
Applications
|
Automotive |
Bottling |
Chemicals |
Food |
|
- Closed Circuit Cooling - Dynamometers - Extruders - Molders - Radiators - Welders |
- CO2 Generators - Heaters - Exchangers - Rinse Tanks - Sterilizers and Washers |
- Dryers - Extruders - Kettles - Mixers - Reactors - Scrubbers - Vacuum Pumps |
- Condensers - Ice Machines - Kathabars - Refrigeration Equipment - Steam Tables |
|
Manufacturing |
Metals |
Mining |
Paper |
|
- Chillers - Compressors - Furnaces - Quenchers - Vacuum Pumps |
- Bearings - Conveyors - Fans - Hearth & Vacuum Furnaces - Shelters - Sprays |
- Bearings - Conveyors - Filters - Presses - Process Lines - Radiators |
- Calendar Rolls - Mill Rolls - Caustic Lines - Scrubbers - Compressors - Liquor Tanks - Pulverizers - Vacuum Pumps |
|
Pharmaceutical |
Refinery |
Rubber & Plastics |
Steel |
|
- Exchangers - Loop Systems - Kathabars - Pumps - Reactors - Stills - Sterilizers |
- Compressors - Converters - Crackers - Exchangers - Piping - Pumps |
- Banbury Mixers - Calendar & Mill Rolls - Extruders - Injection Molders - Molds - Temperature Control - Units - Throat Coolers - Towers and Tubers |
Bearings ConCast Units Generators Hearths Spangle Units Furnaces |
|
Textile |
Utilities |
Other Applications |
|
|
- Air Washers - Compressors - Condensers - Exchangers - Extruders and Towers |
- Boilers - Turbines - Transformers - Cooling Towers - Air Compressors - Hydrogen Coolers - Lube Oil Heat Exchangers |
- Ball Mills - Demisters - Evaporators - Locomotives - Absorption Units - Diesel Generators - Induction Furnaces |
Pooperties:-
|
Appearance: |
Pale yellow or Brown Liquid |
|
|
|
Density, in g/cm3 at 15°C: |
1.2 |
|
|
|
Flash Point, (PMCC) in °C: |
N/A |
|
|
|
pH, in conc: |
< 1.5 |
|
|
|
Compatibility: |
|
|
|
|
Metal: |
Contains corrosion inhibitors. |
|
|
|
Rubber: |
No known effect. |
|
|
|
Synthetic rubber: |
May swell. |
|
|
|
PACKAGING: |
Product no: |
Size (in litres): |
Container: |
|
|
RXSOL-16-1008-210 |
25/50 |
Plastic |
Why Use RXSOL Descaler?
- It is a safe , economical concentrated chemical to be used on the waterside of heat transfer equipment.
-
You do not have to heat RXSOL 1008 .
RXSOL 1008 is safer for the employees to use than other acid products. -
Your equipment will be cleaned in only hours without disassembling any part of the equipment. Equipment can also be cleaned without any down time (cleaning on the run).
- Cleans down to the original surface without pitting.
- RXSOL 1008 is safe on copper, copper-nickel, bronze, brass, iron, stainless steel and rubber.
- RXSOL 1008 will extend the usable life of your equipment, especially when used as a part of a regularly scheduled preventative maintenance program.
- Removing the scale build up allows your equipment to operate more efficiently with less down time.
Do not use concentrated 1008 on aluminium surfaces
| Product Name | Rxsol-16-1008-210 |
| Product Type | DESCALING LIQUID |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Stock Point : Mumbai, Gandhidham, Chennai, Kolkata, Vizag, Fujairah, Barka Muscat
| Phone | +91 22 45151919 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| support@rxmarine.info |
| Chemica Name | Concentration | CAS Number | EC Number | R Phrases* |
|
Chlorous Acid |
20-40 | 7647-01-0 | 231-595-7 | 34, 37 |
| Corrosion Inhibitor | 5-10 | NA | NA | NA |
| Citric-Sulfamic Proprietory Blend | 10-20 | Proprietory | NA | NA |
| Phosphoric acid | 20-32 |
7664-38-2 |
NA | NA |
*See Section 16
Corrosive
| Odour | Strong Smell |
| Appearance | Liquid, pale yellow, soluble in water |
| Contact with eyes | Can cause damage to the eyes |
| Contact with skin | Prolonged skin or eye contact may cause chemical burns |
| Inhalation | Causes severe irritation, May cause breathing difficulty |
| Ingestion | Not regarded as a potential route of exposure.,Causes burning sensation |
| Contact with skin |
Remove contaminated clothing immediately and drench affected skin with plenty of water. Then wash with soap and water When in doubt or symptoms persist, seek medical attention Contaminated clothing should be laundered before reuse |
|
Contact with eyes |
If substance has got into eyes, immediately wash out with plenty of water for at least 15 minutes Irrigate eyes thoroughly whilst lifting eyelids Seek immediate medical attention Continue flushing with water until medical help arrives |
| Ingestion | Never make an unconscious person vomit or drink fluids Give plenty of water to drink Do not induce vomiting Seek immediate medical attention |
| Inhalation |
Remove patient to fresh air Keep warm and at rest, in a half upright position. Loosen clothing When in doubt or symptoms persist, seek medical attention |
| General | In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible) (S45) |
|
- Non combustible |
| Personal Precautions | Wear protective clothing as per section 8 Vapours are heavier than air and may travel considerable distances to a source of ignition and flashback |
| Environmental Precautions | Do not allow to enter public sewers and watercourses |
| Immediate Actions | Use appropriate containment to avoid environmental contamination (S57) |
| Clean Up Actions | Absorb spillage in inert material and shovel up Ventilate the area and wash spill site after material pick-up is complete |
| Special Precautions | Wear protective clothing as per section 8 Avoid release to the environment. Refer to special instructions/Safety data sheets (S61) Vapours are heavier than air and may travel considerable distances to a source of ignition and flashback |
| Handling | Avoid contact with skin and eyes (S24/25) |
| Do not breathe vapour/fumes (S23) | |
| Eyewash bottles should be available | |
| Wear protective clothing as per section 8 | |
| Ensure adequate ventilation | |
| In use, may form flammable/explosive vapour-air mixture (R18) | |
| Storage | Keep only in the original container in a cool, well ventilated place (S3/9/49) |
| Keep in acid store |
| Exposure Limits | TLV (TWA) 20 ppm, 122 mg/m3 (1,2-Dichlorobenzene) |
| Exposure controls | The undiluted product must not be used in a confined space without good ventilation |
| Occupational exposure controls |
Wear approved respirator if exposure likely to exceed MEL/OES Wear goggles giving complete eye protection Wear suitable protective clothing, including eye/face protection and gloves (neoprene or nitrile are recommended) |
Gloves Suit Visor
| Odour | Strong Smell |
| Appearance | Liquid, pale yellow, soluble in water |
| PH | 1.5 at 100 % concentration |
| Boiling point | ~ 100 °C at 760 mm /Hg |
| Vapour pressure | 105.5 at 20 deg C |
| Vapour density (air = 1) | 1.26 |
| Freezing point~ | 30 °C at 760 mm/Hg |
| Completely soluble in water | |
| Specific gravity (water=1) | 1.16 |
| Non combustible | |
|
- This article is considered stable under normal conditions, May cause rubber to swell - Avoid overheating - Incompatible with strong oxidizing substances, Contact with alkaline earth metals may form explosive gases, Contact with alkali metals may form explosive gases - See Section 5 |
| Contact with skin | In cases of severe exposure, redness and irritation may develop |
| Contact with eyes | Causes irritation |
| Ingestion | May cause gastro-intestinal disturbances |
| Carcinogenicity | No evidence of carcinogenic effects |
| Ecotoxicity | This product does not contain ingredients which are classified in the EU as dangerous for theenvironment. |
| Mobility | Completely soluble in water |
| Persistence and Biodegradability | Its main ingredients will either dissolve rapidly and dissociate in water or are readily/inherently biodegradable. |
| Bioaccumulation Potential | Bioaccumulation of the components in this product is insignificant. Other Adverse Effects No environmental problems are expected when the product is used / handled correctly. |
|
Classification |
This material and/or its container must be disposed of as hazardous waste EU Waste class Disposal considerations Do not discharge into drains or the environment, dispose to anauthorised waste collection point Disposal should be in accordance with local, state or national legislation |
| Proper Shipping Name: | ||||
| UN | ||||
| Proper Shipping Name: | Phosphoric solution Blend | |||
| UN NO. |
1805 |
|||
| Hazard Class | 8 | PackingGroup | II | |
|
Road/Rail(ADR/RID) |
||||
| Proper Shipping Name |
Phosphoric solution Blend |
|||
| ADR UN No. |
1805 |
|||
|
ADRHazardClass |
8 | Tremcard |
80GC1789-II |
|
| Sear (IMDG) | ||||
| Proper Shipping Name |
Phosphoric solution Blend |
|||
| IMDG UN No. |
1805 |
|||
| IMDG Hazard Class | 8 | IMDG PackGroup.: |
II |
|
| IMDG EmS | F-A, S-B | IMDG subrisk |
N/A |
|
|
IMDG Labels |
8 |
IMDG Flashpoint: |
N/A |
|
|
Air(ICAO/IATA) |
||||
| ProperShippingName |
Phosphoric solution Blend |
|||
| IMDG UNNo |
1805 |
|||
| IMDG HazardClass | 8 | ICAO PackingGroup |
II |
|
| ICAO subrisk | N/A | ICAO Labels: |
8+CAO |
|
| ICAO Flashpoint |
N/A |
|||
|
DOT/ CFR(USDepartment ofTransportation |
||||
|
DOTProperShippingName |
Phosphoric solution Blend |
|||
|
HazardousMaterial |
Phosphoric solution Blend |
|||
| HazardClass | 8 | IdentificationNumber: | UN1805 | |
|
Product RQ (lbs) |
N/E | DOTsubrisk: |
N/A |
|
|
DOTLabels |
8 |
DOTFlashpoint: | N/A | |
- Not classified as hazardous for transport
| Risk Phrases | Irritating to eyes (R36) |
| Safety Phrases Irritant | In case of contact with eyes, rinse immediately with plenty of water and seek medical advice (S26)Wear suitable gloves and eye/face protection (S37/39) |
|
Text of R and S phrase codes used in this safety data sheet:- |
|
| R34 | Causes burns; |
| R36 | Irritating to eyes; |
| R37 | Irritating to respiratory system; |
| R41 | Risk of serious damage to eyes. |
| The information provided about the product on this Safety Data Sheet has been compiled from knowledge of the individual constituents The data given here is based on current knowledge and experience. This Safety Data Sheet describes the product in terms of safety requirements and do- es not signify any warranty with regard to the product's properties The data given here only applies when product used for proper application(s). The product is not sold as suitable for other applications - usage in such may cause risks not mentioned in this sheet. Do not use for other application(s) without seeking advice from manufacturer This Safety Data Sheet is provided in compliance with The Dangerous Substances Directive (67/548/EEC) This Safety Data Sheet is provided in compliance with The Dangerous Preparations Directive (88/379/EEC) This Safety Data Sheet is provided in compliance with The Safety Data Sheets Directive (2001/58EC) Composition information in accordance with Regulation (EC) No 648 /2004 of the European Parliament and of the Council of 31 March 2004 on detergents: Nonionic surfactants 5-15 % Amphoteric surfactants 5 | |
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.