Corrosion Inhibitor for metal RUST Preventive is a general purpose solvent based corrosion preventive. It is an organic rust inhibitor, which has water displacing properties and is a fingerprint neutralizer. The protective coating is thin, transparent, clear and slightly oily.
Application or immersion type dewatering and protective fluid.
Corrosion Inhibitor for metal RUST Prevantive protects all ferrous and non-ferrous metals during processing, indoor storage and wrapped shipment (up to 12 months).
Corrosion Inhibitor for metal RUST Preventive is a “natural” for the bearing industry. Finished bearings can be dipped in Corrosion Inhibitor for metal RUST Prevantive to displace water-based metalworking fluids and provide corrosion protection of the highly finished parts during wrapped shipment. It can also be used for automotive parts and other precision and semi-precision parts.
RECOMMENDED STARTING DILUTIONS
Corrosion Inhibitor for metal RUST Preventive is to be used as is. Add no other materials to dilute the concentration unless approved by RX Marine International technical team.
TYPICAL PHYSICAL AND CHEMICAL PROPERTIES:
| Physical State | : | Liquid |
| Solubility in Water | : | Insoluble |
| Boiling Point | : | >190°F |
| Flash Point, COC | : | 190°F |
| Total Chlorine/Chloride, wt% | : | 0.00/0.00ppm |
| Appearance and Odor | : | Opaque/Chemical |
| Specific Gravity | : | 0.82 |
| VOC Content (ASTM D2369) | : | 58% |
| pH Concentrate | : | NA |
| Total Sulfur, wt% | : |
0.00 |
FEATURES & BENEFITS
VERSATILE:
Corrosion Inhibitor for metal RUST Preventive rapidly displaces water from metal surfaces leaving a continuous polar protective film between the metal and water.
Corrosion Inhibitor for metal RUST Prevantive is applied with in-process spray or dip tank application where fluid run-off is collected for reuse; water will settle quickly to the bottom of the rust preventative reservoir. The water can then be drained periodically from the bottom.
Corrosion Inhibitor for metal RUST Prevantive can be applied to wet or dry parts. It neutralizes fingerprint residues and protects ferrous and non-ferrous metals from corrosion.
Nitrite , Mercaptobenzothiazole (MBT),Metasilicate as a Aluminium protector , Borate
Corrosion Inhibitor for metal RUST Prevantive is a “natural” for the bearing industry. Finished bearings can be dipped in Corrosion Inhibitor for metal RUST Prevantive to displace water-based metalworking fluids and provide corrosion protection of the highly finished parts during wrapped shipment. It can also be used for automotive parts and other precision and semi-precision parts.
| Product Name | : | RXSOL-16-1027 |
| Product Type | : | RUST Preventive Metal Corrosion Inhibitor |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Stock Point : Mumbai, Kandla, Kolkata, Chennai, Vizag, Fujairah, Muscat
| Phone | : | +91 22 65113333 / 5555 / 9999 / 27611360 |
| Fax | : | +91 22 2781 1318 :::AOH :0091 9821214367 |
| : | mail@rxmarine.com |
|
Ingredient(s) |
CAS Number |
% (by Weight) |
|
Aliphatic Hydrocarbons (Stoddard Type) |
8052-41-3 |
20.0 - 30.0 |
|
Aliphatic Petroleum Distillates |
64742-47-8 |
9.0 - 19.0 |
| Nitrite | 7632-00-0 | 10-20 |
| Mercaptobenzothiazole (MBT) | 149-30-4 | 5-10 |
| Metasilicate as a Aluminium protector | 6834-92-0 | 10-15 |
| Borate | 1330-34-4 | 6-10 |
Potential Health Effects
| Eye | Can cause eye irritation. Symptoms include stinging, tearing, redness, and swelling of eyes. |
| Skin | Can cause skin irritation. Prolonged or repeated contact may dry the skin. Symptoms may include redness, burning, and drying and cracking of skin, burns and other skin damage. Passage of this material into the body through the skin is possible, and may add to toxic effects from breathing or swallowing. |
| Swallowing | Swallowing small amounts of this material during normal handling is not likely to cause harmful effects. Swallowing large amounts may be harmful. This material can enter the lungs during swallowing or vomiting and cause lung inflammation and/or damage. |
| Inhalation | Breathing of vapor or mist is possible. Breathing small amounts of this material during normal handling is not likely to cause harmful effects. Breathing large amounts may be harmful. |
| Symptoms of Exposure | Stomach or intestinal upset (nausea, vomiting, diarrhea), irritation (nose, throat, airways), central nervous system depression (dizziness, drowsiness, weakness, fatigue, nausea, headache, unconsciousness), and death. |
| Target Organ Effects | Overexposure to this material (or its components) has been suggested as a cause of the following effects in laboratory animals, and may aggravate preexisting disorders of these organs in humans: blood abnormalities, liver abnormalities, anemia, spleen damage, testis damage, kidney damage, lung damage, Overexposure to this material (or its components) has been suggested as a cause of the following effects in humans, and may aggravate preexisting disorders of these organs: central nervous system effects. |
| Developmental Information | This material (or a component) has been shown to cause harm to the fetus in laboratory animal studies. Harm to the fetus occurs only at exposure levels that harm the pregnant animal. The relevance of these findings to humans is uncertain. |
| Cancer Information | No data |
| Other Health Effects | No data |
| Primary Route(s) of Entry | Inhalation, Skin absorption, Skin contact. |
| Eyes | If symptoms develop, immediately move individual away from exposure and into fresh air. Flush eyes gently with water for at least 15 minutes while holding eyelids apart; seek immediate medical attention. Skin Remove contaminated clothing. Wash exposed area with soap and water. If symptoms persist, seek medical attention. Launder clothing before reuse. |
| Skin | Remove contaminated clothing. Wash exposed area with soap and water. If symptoms persist, seek medical attention. Launder clothing before reuse. |
| Swallowing | Do not induce vomiting. This material is an aspiration hazard. If individual is drowsy or unconscious, place on left side with the head down. Seek medical attention. If possible, do not leave individual unattended. |
| Inhalation | If symptoms develop, immediately move individual away from exposure and into fresh air. Seek immediate medical attention; keep person warm and quiet. If person is not breathing, begin artificial respiration. If breathing is difficult, administer oxygen. |
| Note to Physicians | No data |
| Flash Point | 106.0 F (41.1 C) PMCC |
| Explosive Limit | (for component) Lower 1.0 Upper 7.0 % |
| Autoignition Temperature | No data |
| Hazardous Products of Combustion | May form: carbon dioxide and carbon monoxide, various hydrocarbons |
| Fire and Explosion Hazards | Vapors are heavier than air and may travel along the ground or be moved by ventilation and ignited by heat, pilot lights, other flames and ignition sources at locations distant from material handling point. Never use welding or cutting torch on or near drum (even empty) because product (even just residue) can ignite explosively. |
| Extinguishing Media | regular foam, carbon dioxide, dry chemical. |
| Fire Fighting Instructions | Water or foam may cause frothing which can be violent and possibly endanger the life of the firefighter. Wear a self-contained breathing apparatus with a full facepiece operated in the positive pressure demand mode with appropriate turn-out gear and chemical resistant personal protective equipment. Refer to the personal protective equipment section of this MSDS. |
| NFPA Rating | Health - 1, Flammability - 2, Reactivity - 0 |
| Small Spill | Absorb liquid on vermiculite, floor absorbent, or other absorbent material and transfer to hood. |
| Large Spill | Eliminate all ignition sources (flares, flames including pilot lights, electrical sparks). Persons not wearing protective equipment should be excluded from area of spill until clean-up has been completed. Stop spill at source. Prevent from entering drains, sewers, streams or other bodies of water. Prevent from spreading. If runoff occurs, notify authorities as required.Pump or vacuum transfer spilled product to clean containers for recovery. Absorb unrecoverable product. Transfer contaminated absorbent, soil and other materials to containers for disposal. Prevent run-off to sewers, streams or other bodies of water. If run-off occurs, notify proper authorities as required, that a spill has occured. |
| Handling | Containers of this material may be hazardous when emptied. Since emptied containers retain product residues (vapor, liquid, and/or solid), all hazard precautions given in the data sheet must be observed. All five gallon pails and larger metal containers including tank cars and tank trucks should be grounded and/or bonded when material is transferred. |
| Storage | Not applicable |
| Eye Protection | Chemical splash goggles in compliance with OSHA regulations are advised; however, OSHA regulations also permit other type safety glasses. Consult your safety representative. |
| Skin Protection | Wear resistant gloves such as: neoprene, nitrile rubber, To prevent repeated or prolonged skin contact, wear impervious clothing and boots.. |
| Respiratory Protections | If workplace exposure limit(s) of product or any component is exceeded (See Exposure Guidelines), a NIOSH/MSHA approved air supplied respirator is advised in absence of proper environmental control. OSHA regulations also permit other NIOSH/MSHA respirators (negative pressure type) under specified conditions (consult your industrial hygienist). Engineering or administrative controls should be implemented to reduce exposure. |
| Engineering Controls | Provide sufficient mechanical (general and/or local exhaust) ventilation to maintain exposure below TLV(s). |
| Exposure Guidelines Component |
ALIPHATIC HYDROCARBONS (STODDARD TYPE) (8052-41-3) OSHA VPEL 100.000 ppm - TWA ACGIH TLV 100.000 ppm - TWA ALIPHATIC PETROLEUM DISTILLATES (64742-47-8) No exposure limits established |
| Boiling Point | (for component) 315.0 F (157.2 C) @ 760 mmHg |
| Vapor Pressure | (for component) 2.000 mmHg @ 68.00 F |
| Specific Vapor Density | No data |
| Liquid Density |
7.420 lbs/gal @ 60.00 F .891 kg/l @ 15.60 C |
| Percent Volatiles (Including Water) | 42.0 - 48.0 % |
| Volitile Organic Compounds (VOC) (Maximum) | 3.150 lbs/gal |
| Evaporation Rate | SLOWER THAN ETHYL ETHER |
| Appearance | Brownish Liq |
| State | LIQUID |
| Physical Form | Liquid |
| Color | Dark |
| Odor | Characteristic Smell |
| pH | 4-7 |
| Hazardous Polymerization | Product will not undergo hazardous polymerization. |
| Hazardous Decomposition | May form: carbon dioxide and carbon monoxide, various hydrocarbons. |
| Chemical Stability | Stable |
| Incompatibility | Avoid contact with: strong oxidizing agents. |
- No Data
- No Data
- Waste Management Information
- Destroy by liquid incineration. Dispose of in accordance with all
- applicable local, state and federal regulations.
| DOT Information | : | 49 CFR 172.101 |
| DOT Description | : | Not Regulated |
| Container/Mode | : | DRUMS/SURFACE - NO EXCEPTIONS |
| NOS Component | : | PETROLEUM NAPHTHA |
| RQ (Reportable Quantity) - 49 CFR 172.101 | : | Not applicable |
| US Federal Regulations | TSCA (Toxic Substances Control Act) Status | |
| TSCA (UNITED STATES) | The intentional ingredients of this product are listed. | |
| CERCLA RQ | 40 CFR 302.4 | None |
| SARA 302 Components | 40 CFR 355 Appendix A | None |
| Section 311/312 Hazard Class | 40 CFR 370.2 |
Immediate(X) Delayed(X) Fire(X) Reactive( ) Sudden Release of Pressure( ) |
| SARA 313 Components | 40 CFR 372.65 | None |
| International Regulations | Inventory Status | Not determined |
| State and Local Regulations | California Proposition 65 | None |
| New Jersey RTK Label Information | STODDARD SOLVENT | 8052-41-3 |
| Pennsylvania RTK Label Information | STODDARD SOLVENT | 8052-41-3 |
The information accumulated herein is believed to be accurate but is not warranted to be whether originating with the company or not. Recipients are advised to confirm in advance of need that the information is current, applicable, and suitable to their circumstance.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.