Commissioning Cleanser is a multi functional surfactant based cleaner. It is the new generation in one step cleaner product with low foaming and very effective.
Commissioning Cleanser is for cleaning of new boilers and cooling systems on board new buildings. It will remove scale, rust, oil and grease at the same time from the systems. The product is recirculated through the system, using an external circulation pump.
Use the dosage 5-10% solution depending on the grade of contamination.
Degreasing and descaling of boiler and cooling water systems
Drain system to be cleaned if necessary.
- Inspect as completely as possible to determine the extent of contamination and general condition of system.
- Fill with fresh water.
- Add a solution 5-10% strength of Commissioning Cleanser.
- Circulate through the system for 5 to 8 hours at the maximum temperature allowed by the system.
- Drain system complete and flush thoroughly the entire system and all compounds with fresh water until effluent is clear.
- Reinspect to determine results of the cleaning process.
- If unsatisfactory, repeat steps 3 through 7.
- Refill system with distillate or good quality fresh water and dose the required amount of cooling or boiler water treatment.
- Test system on a regular basis to insure chemical residuals are maintained with specific limits.
| Odour | Odourless |
| Appeearance | Liquid Off White |
| Specific Vapor Density | No data |
| Liquid Density | 1.12 at 20 °C |
| pH | 8.5-9.0 |
| Boiling Point | 100 °C at 760 mm /Hg |
Water based multifunctional cleaner. Biodegradable. Does not contain nonyl phenol ethoxylates or other estrogenic compounds.
Cleaning of new systems for mill scale, rust, oil etc..
Cleans water systems with light scale and a thin oil film. Provides a temporary protection against corrosion by passivation.
No need of neutralization chemicals afterwards. Safe on aluminium, zinc, tin and their alloys. Quick separation of oil after cleaning.
| Product Name | : | RXSOL-16-1078-210 |
| Product Type | : | Commissioning Cleanser |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | : | +91 22 65113333 / 5555 / 9999 / 27611360 |
| Fax | : | +91 22 2781 1318 :::AOH :0091 9821214367 |
| : | mail@rxmarine.com |
|
Ingredient(s) |
CAS Number |
% (by Weight) | Symbol |
|
Trisodium N-hydroxyethyl ethylenediamine triacetate |
139-89-9 |
10-30 | Xi |
|
2-Ethyl hexyl oxypropyliminopropionic acidmono sodium salt |
94441-92-6 |
1-5 | Xi |
| 2-2(butoxyethoxy)ethanol | 112-34-5 | 1-5 | Xi |
Classification of the substance
Irritant
Risk Phrases
- Irritating to eyes and skin (R36/38)
Safety Phrases
- In case of contact with eyes, rinse immediately with plenty of water and seek medical advice (S26)
- Wear suitable gloves and eye/face protection (S37/39)
Other hazards
- Odour: Odourless
- Appearance: Liquid, off-white, miscible with water
- Contact with eyes: May cause redness and irritation
- Contact with skin: May cause irritation, Repeated exposure may cause skin dryness or cracking (R66)
- Inhalation: May cause irritation
- Ingestion: Not regarded as a potential route of exposure., May cause irritation
Description of first aid measures
- IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if
present and easy to do. Continue rinsing.
- IF INHALED: If breathing is difficult, remove to fresh air and keep at rest in a position
comfortable for breathing.
- IF ON SKIN: Wash with plenty of soap and water.
- IF SWALLOWED: rinse mouth. Do NOT induce vomiting.
- Give plenty of water to drink
- Never make an unconscious person vomit or drink fluids
Most important symptoms and effects, both acute and delayed
- Possible redness and irritation of affected areas
- In cases of severe exposure, irritation may develop
Indication of immediate medical attention and special treatment needed
|
Fire-fighting measures |
Not flammable. In case of fire use extinguishing media appropriate to surrounding conditions No Hazard Expected under normalcondition of use. Wear chemical Protection Suit and Positive-Pressure Brathing appartus |
Personal precautions, protective equipment and emergency procedures
- Wear protective clothing as per section 8
Environmental Precautions
- Do not allow to enter public sewers and watercourses
- Avoid release to the environment.
Methods and material for containment and cleaning up
- Absorb spillage in suitable inert material
- Sweep or shovel-up spillage and remove to a safe place
- Flush spill area with copious amounts of water
Reference to other sections
- Non
Precautions for safe handling
- Wear protective clothing as per section 8
- Do not get in eyes, on skin, or on clothing.
- Eyewash bottles should be available
Conditions for safe storage, including any incompatibilities
- Keep only in the original container in a cool, well ventilated place away from water (S3/9/14/49)
- Protect from frost
Specific end use
| Eye Protection | Chemical splash goggles in compliance with OSHA regulations are advised; however, OSHA regulations also permit other type safety glasses. Consult your safety representative. |
| Skin Protection | Wear resistant gloves such as: neoprene, nitrile rubber, To prevent repeated or prolonged skin contact, wear impervious clothing and boots.. |
| Respiratory Protections | If workplace exposure limit(s) of product or any component is exceeded (See Exposure Guidelines), a NIOSH/MSHA approved air supplied respirator is advised in absence of proper environmental control. OSHA regulations also permit other NIOSH/MSHA respirators (negative pressure type) under specified conditions (consult your industrial hygienist). Engineering or administrative controls should be implemented to reduce exposure. |
| Engineering Controls | Provide sufficient mechanical (general and/or local exhaust) ventilation to maintain exposure below TLV(s). |
| Odour | Odourless |
| Appeearance | Liquid Off White |
| Specific Vapor Density | No data |
| Liquid Density | 1.12 at 20 °C |
| pH | 8.5-9.0 |
| Boiling Point | 100 °C at 760 mm /Hg |
Reactivity
- This article is considered stable under normal conditions
Chemical stability
- Considered stable under normal conditions
Possibility of hazardous reactions
- No hazardous reactions known if used for its intended purpose
Conditions to avoid
- No special precautions are required for this product
Incompatible materials
- None
Hazardous Decomposition Products
- No hazardous decomposition products known
Information on toxicological effects
- LD50 (oral,rat) >2000 mg/kg
Inhalation
- Causes irritation
Contact with skin
- Prolonged skin contact will result in defatting of the skin, leading to irritation, and in some cases, dermatitis May cause irritation
Contact with eyes
- Causes redness and irritation
Ingestion
- The ingestion of significant quantities may cause gastro-intestinal disturbances
Toxicity
- LC50 (fish) (Trisodium hydroxyethyl ethylenediamine triacetate) >100 mg/l (96 hr)
- LC50 (fish) (dipropionate) >100 mg/l (96 hr)
- LC50 (fish) (2-(2-butoxyethoxy)ethanol) 2500 mg/l (96 hr)
- This product does not contain ingredients which are classified in the EU as dangerous for the environment.Persistence and degradability
- Biodegradability. OECD-test. 28 days 20 % (Trisodiumhydroxyethylethylenaminetriacetat)
- Biodegradability. OECD-test. 28 days >60 % (Sodiumcapryliminodipropionate)
- Biodegradability. OECD-test. 28 days >60 % (2-(2-buhtoxyetoxy)etanol)
Bioaccumulation Potential
- No information available
Mobility in soil
- Completely soluble in water
Results of PBT and vPvB assessment
- Not a PBT according to REACH Annex XIII
Other Adverse Effects
- Presents little or no hazard to the aquatic environment
Waste Management Information
- Destroy by liquid incineration. Dispose of in accordance with all applicable local, state and federal regulations.
UN Number
- n/a
UN Proper Shipping Name
- n/a
Transport hazard class(es)
- n/a
Packing group
- n/a
Environmental hazards
- On available data, substance is not harmful to the environment
Special precautions for user
- Not classified as hazardous for transport
Transport in bulk according to Annex II of MARPOL 73/78 and the IBC code
- Not applicable
Safety, health and environmental regulations/legislation specific for the substance or mixture
- This Safety Data Sheet has been prepared in accordance with article 31 and annex II in
REACH and Directive 453/2010/EU.
- Regulations 1272/2008/EEC. Classification, labeling and packing of dangerous substances
and preparations
- Counsil Directive 1999/45/EEC Classification, packing and labelling of dangerous
preparations.
- Refer to The Dangerous Substances Directive (67/548/EEC)
- Composition
- Nonionic surfactants 5 %
- Amphoteric surfactants 5 %
- phosphonates 5%
Chemical Safety Assessment
NONE
Text of R and S phrase codes used in this safety data sheet:- R36: Irritating to eyes; R41: Risk of serious damage to eyes.The information provided about the product on this Safety Data Sheet has been compiled from knowledge of the individual constituents . The data given here is based on current knowledge and experience. This Safety Data Sheet describes the product in terms of safety requirements and does not signify any warranty with regard to the product's properties. The data given here only applies when product used for proper application(s). The product is not sold as suitable for other applications - usage in such may cause risks not mentioned in this sheet. Do not use for other application(s) without seeking advice from manufacturer
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.