RXSOL ANTI CORROSIVE AGENT is a solvent cutback, wax base, general purpose, corrosion preventive compound.RXSOL ANTI CORROSIVE AGENT is excellent for long term protection of metallic surfaces against corrosion in either indoor or outdoor exposure and during domestic and international shipments, like machinery, machine rolls/tools, automatic parts, dies, tubing, and spare parts.RXSOL ANTI CORROSIVE AGENT cures to a dark amber colored, waxy, transparent, firm film.
RXSOL ANTI CORROSIVE AGENT is formulated to be used as supplied. Ensure uniform consistency prior to use. Continued stirring is generally not required. If the product thickens due to cold storage or loss of solvent during use, contact Valvoline. DO NOT THIN RXSOL ANTI CORROSIVE AGENT. Incorrect thinning will affect film build, dry time and product performance.Rx Marine International recommends that the ambient and product temperature be 10-35 °C at the time of product application. RXSOL ANTI CORROSIVE AGENT can be applied by airless spray or brush.
Net Materials by spray machine or Brush.
Typical Properties
| Flashpoint; PMCC | 40 | °C |
| Specific Gravity @ 60°F | 0.87 | kg/ltr |
| Recommended Dry Film Thickness | 50 | microns minimum |
| Theoretical Coverage @ Avg. Recommended DFT | 9.2 | m²/l |
| Non Volatile | 52 | weight % |
|
Viscosity; DIN (53 211) Cup No. 4 @ 20°C (at time of manufacture) |
85 | seconds |
| Dry to Touch Time @ 25°C | ± 2 | hours |
| Cure Time @ 25°C | ± 24 |
hours |
| Volatile Organic Content (VOC) (ASTM D-3960) | 415 | g/l |
Accelerated Corrosion Tests:
@ Avg. Recommended DFT
| Salt Spray; 5 % NaCl @ 35°C; DIN 50 021 (ASTM B-117) (DIN 1623 Steel Panels) | 40+ |
days |
| Humidity; 100 % RH; @ 40°C; DIN 50 017-KK (DIN 1623 Steel Panels) | 100+ |
days |
Removal:
RXSOL ANTI CORROSIVE AGENT can be removed with mineral spirits or any similar petroleum solvent, hot alkaline wash or low pressure steam.
Storage:
RXSOL ANTI CORROSIVE AGENT should be stored at temperatures between 10-35 °C. Mild agitation is recommended prior to use. Due to its composition RXSOL ANTI CORROSIVE AGENT can be subject to postproduction viscosity changes during storage.Under proper storage conditions RXSOL ANTI CORROSIVE AGENT can have a shelf life of 4 years minimum.
Caution:
Adequate ventilation is required for cure and to ensure against formation of combustible liquid. THE PARTIALLY CURED FILM SHOULD NOT BE EXPOSED TO IGNITION SOURCES SUCH AS FLARES, FLAMES, SPARKS, EXCESSIVE HEAT OR TORCHES. Refer to Material Safety Data Sheet for additional handling and first aid information.
Note:
The addition of any product over or under this coating is not recommended. The use of additional coatings could result in chemical incompatibility, thus affecting the performance of this coating as stated in the Typical Properties section.
| Product Name | RXSOL-16-1752-025 |
| Product Type | Anti Corrosive Agent |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Stock Point : Chennai, Kolkata, Mumbai, Kandla, Visakhapatnam, Fujairah, Muscat, Nairobi
| Phone | +91 22 27815541 / 42 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| mail@rxmarine.com |
| HAZARDOUS INGREDIENTS | Wt. |
Recommended Exposure Limits |
| Aliphatic Hydrocarbons (Stoddard Type)CAS #8052-41-3 | 20-30 |
OSHA PEL: 100 ppm ACGIH TLV: 100 ppm |
|
NON-HAZARDOUS INGREDIENTS |
||
|
Calcium Salt Of Oxidized Petrolatum CAS #68425-34-3 |
60-65 | None Established |
| Residual oils, petroleum, solvent refined CAS #64742-01-4 | 10-13 | ACGIH TLV: 5 mg/m3 |
Eye: Can cause eye irritation. Symptoms include stinging, tearing, redness, and swelling of eyes.
Skin: May cause mild skin irritation. Prolonged or repeated contact may dry the skin. Symptoms may include redness, burning, drying and cracking of skin, and skin burns
Swallowing: Swallowing small amounts of this material during normal handling is not likely to cause harmful effects. Swallowing large amounts may be harmful. This material can enter the lungs during swallowing or vomiting and cause lung inflammation and/or damage.
Inhalation: Breathing of vapor or mist is possible. Breathing small amounts of this material during normal handling is not likely to cause harmful effects. Breathing large amounts may be harmful.
Symptoms of Exposure: stomach or intestinal upset (nausea, vomiting, diarrhea), irritation (nose, throat, airways), central nervous system depression (dizziness, drowsiness, weakness, fatigue, nausea, headache, unconsciousness).
Target Organ Effects: Overexposure to this material (or its components) has been suggested as a cause of the following effects in humans, and may aggravate pre-existing disorders of these organs: central nervous system effects.
Developmental Information: No data
Cancer Information: No data
Other Health Effects: No data
Primary Route(s) of Entry: Inhalation, Skin contact.
| Eyes: | If symptoms develop, immediately move individual away from exposure and into fresh air. Flush eyes gently with water for at least 15 minutes while holding eyelids apart; seek immediate medical attention. |
| Skin: | Remove contaminated clothing. Wash exposed area with soap and water. If symptoms persist, seek medical attention. Launder clothing before reuse. |
| Swallowing: | Do not induce vomiting. This material is an aspiration hazard. It individual is drowsy or unconscious, place on left side with the head down. Seek medical attention. If possible, do not leave individual unattended. |
| Inhalation: | If symptoms develop, immediately move individual away from exposure and into fresh air. Seek immediate medical attention; keep person warm and quiet. It person is not breathing, begin artificial respiration. If breathing is difficult, administer oxygen. |
| Note to Physicians: | No data |
| Flash Point: | 106 oF (41.1 oC) PMCC |
| Explosive Limit: | (for component) Lower 1.0 Upper 6.0 % |
| Autoignition Temperature: | No data |
| Hazardous Products of Combustion: | May form: carbon dioxide and carbon monoxide, sulfur compounds, various hydrocarbons. |
| Fire and Explosion Hazards: | Vapors are heavier than air and may travel along the ground or be moved by ventilation and ignited by heat, pilot lights, other flames and ignition sources at locations distant from material handling point. Never use welding or cutting torch on or near drum (even empty) because product (even just residue) can ignite explosively. |
| Extinguishing Media: | regular foam, carbon dioxide, dry chemical. |
| Fire Fighting Instructions: | Water may be used to extinguish fire by cooling, and diluting liquid with water. Wear a selfcontained breathing apparatus with a full facepiece operated in the positive pressure demand mode with appropriate turn-out gear and chemical resistant personal protective equipment. Refer to the personal protective equipment section of this MSDS. |
| Small Spill: | Eliminate all sources of ignition such as flares, flames (including pilot lights), and electrical sparks. Absorb liquid on vermiculite, floor absorbent or other absorbent material. |
| Large Spill: | Eliminate all ignition sources (flares, flames including pilot lights, electrical sparks). Persons not wearing protective equipment should be excluded from area of spill until clean-up has been completed. Stop spill at source. Prevent from entering drains, sewers, streams or other bodies of water. Prevent from spreading. If runoff occurs, notify authorities as required. Pump or vacuum transfer spilled product to clean containers for recovery. Absorb unrecoverable product. Transfer contaminated absorbent, soil and other materials to containers for disposal. |
| Handling: | Containers of this material may be hazardous when emptied. Since emptied containers retain product residues (vapor, liquid, and/or solid); all hazard precautions given in the data sheet must be observed. All five gallon pails and larger metal containers including tank cars and tank trucks should be grounded and/or bonded when material is transferred. |
| Storage: |
Not applicable |
| Eye Protection: | Chemical splash goggles in compliance with OSHA regulations are advised; however, OSHA regulations also permit other type safety glasses. Consult your safety representative. |
| Skin Protection: | Wear resistant gloves such as: neoprene. To prevent repeated or prolonged skin contact, wear impervious clothing and boots. |
| Respiratory Protections: | If workplace exposure limit(s) of product or any component is exceeded (See Exposure Guidelines), a NIOSH/MSHA approved air supplied respirator is advised in absence of proper environmental control. OSHA regulations also permit other NIOSH/MSH.A respirators (negative pressure type) under specified conditions (consult your industrial hygienist). Engineering or administrative controls should be implemented to reduce exposure. |
| Engineering Controls: | Provide sufficient mechanical (general and/or local exhaust) ventilation to maintain exposure below TLV(s) |
| Boiling Point: | (for component) 315 oF (157.2 oC) |
| Vapor Pressure: |
(for component) 2 mmHg |
| Specific Vapor Density: |
>1 @ AIR=1 |
| Specific Gravity: | .89 @ 77 oF |
| Liquid Density: |
7.31 lbs/gal @ 77 oF (.89 Kg/l @ 25 oC) |
|
Percent Volatiles (Including Water): |
50 — 54 |
|
Volatile Organic Compounds (VOC) (Calculated): |
3.48 lbs/gal |
|
Evaporation Rate: |
Slower Than Ethyl Ether |
| Appearance: | Translucent |
| State: | Liquid |
| Physical Form: | No data |
| Color: | Amber |
| Odor: | No data |
| Ph: | Not applicable |
| Hazardous Polymerization: | Product will not undergo hazardous polymerization. |
| Hazardous Decomposition: | May form: carbon dioxide and carbon monoxide, sulfur compounds, various hydrocarbons. |
| Chemical Stability: | Stable. |
| Incompatibility: | Avoid contact with: strong oxidizing agents. |
None known.
None known.
Waste Management Information: Dispose of in accordance with all applicable local, state and federal regulations.
DOT Information — 49 CFR 172.101
DOT Description: COMBUSTIBLE LIQUID, N.O.S.,NA 1993,111
Container/Mode: DRUMS/SURFACE - NO EXEMPTIONS
NOS Component: ALIPHATIC HYDROCARBONS (STODDARD TYPE)
RQ (Reportable Quantity) — 49 CFR 172.101
Not applicable
Volatile Organic Content: (Calculated Values)
VOC per gallon: 3.48 lbs/gal
EPA Hazard Category (40 CFR Part 370): IMMEDIATE (ACUTE) FIRE (COMBUSTIBLE)
SARA TITLE III:
This product contains the following TOXIC CHEMICALS subject to the Reporting Requirements of Sec. 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986, and of 40 CFR Part 372:
Chemical CAS No. Wt%
None
This product contains the following EXTREMELY HAZARDOUS SUBSTANCE(S) subject to Emergency Planning Requirements under Sec. 301-303 (40 CFR Parts 300 and 355) and Emergency Release Notification Requirements under Sec. 304:
Chemical CAS No. Wt% RQ/TPQ Lbs
None
This product contains the following (CERCLA LIST) HAZARDOUS SUBSTANCE(S) subject to Emergency Release Notification Requirements under Sec. 304 (40 CFR Part 302):
Chemical CAS No. Wt% Final RQ Lbs
None
CALIFORNIA PROPOSITION 65:
This product may contain trace quantities of the following chemicals that are identified by the State of California under the Safe Drinking Water and Toxic Reinforcement Act of 1986 ("Proposition 65") as either a carcinogenic or reproductive hazard:
Chemical CAS No. Estimated Concentration %
None
WHMIS CLASSIFICATION: B2, D2B
Although the information contained herein is believed to be reliable, it is furnished without warranty of any kind. This information is not intended to be all-inclusive as to the manner and conditions of use, handling, and storage.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.