Especially formulated for tank cleaning where Hydro Carbon Free techniques and more concentrated product with less foam is required to soften up / remove baked on drying oils and also used after animal and vegetable oils, fish oils, tall oils,tug oil etc. It is low toxic product with an exceptional solvency power on soil & oily matter .It is free from hydrocarbon solvents and minimizes the extreme hazards to personnel in handling materials.
Powerful solvency
Moderate evaporation rate
Low viscosity
High dilution ratio
Low surface tension
Coupling ability
Wide range of applications
First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-20-2013-025 is by direct injection followed by recirculation washing, using tank cleaning machines.
Using Procedure:-
First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-20-2013-025 is by direct injection followed by recirculation washing, using tank cleaning machines.
Spraying Method:- Using HCF as delivered in drums, spray onto areas where residue remains following rough washing leave for 10-45 minutes (but do not allow to dry), then butterworth at maximum pressure and warm water 60oC for at least 3 hours, checking that there is no foam remaining in the final stages. Inspects tanks(s) and if desired result has been achieved fresh water rinse and dry.
**Make sure to take all safety precautions are followed when handling / spraying HCF**
Injection Method– not applicable.
Re-circulation Method– Fill tank with fresh water and heat up to warm 50oC . IF a drop line is available on the tank line system, then start to circulate the water and add the required amount of Caustic flakes and HCF to make a 2.5% solution. A stronger solution can be made, but be advised that too much Caustic and too high temperature will result in white powder all over the tank. Under normal circumstances, between 2.5% and 4.5% will be sufficient strength. If there is no drop line, then lower butterworth hoses into the tank from the pump stack header without machines attached and circulate through these hoses while you fill the solution material.
** Use a strainer at the pump stack when circulating any solution.**
Tank Lining– Stainless / Epoxy / Phenolic / Zinc-silicate.
Characteristics:
- Removes grease, oil, carbon deposits, soil and grime.
- Keeps loosened deposits in suspension preventing re-deposition.
- Low toxic. , Non-flammable.
- Free from hydrocarbon solvents.
- Effective and economical in use , Water-based cleaner.
- RXSOL-20-2013-025 has numerous cleaning applications including removal of greases, waxes, oil, sludge, soot, carbon deposits and general dirt and grime.
- Non-corrosive to ferrous metals. Suitable for all tank-coatings.
- Can be used for gas and hydrocarbon freeing of tanks.
- Can be used for deodorizing
- Contains wetting agents.
Note:- Completely miscible with sea water.
| Product Name | : | RXSOL-20-2013-025 |
| Product Type | : | HCF REMOVER HD-I |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | : | +91 22 65113333 / 5555 / 9999 / 27611360 |
| Fax | : | +91 22 2781 1318 :::AOH :0091 9821214367 |
| : | mail@rxmarine.com |
* Chemical characterization
* Description: Mixture of the substances listed below with harmless additions.
* Dangerous components:
CAS : 111-76-2 2-butoxyethanol Xn; R 20/21/22-36/38 5-10%
EINECS : 203-905-0
Alco Xi; R 38 7.0%
CAS : 112-34-5 2-(2-butoxyethoxy)ethanol Xi; R 36 2.5-5%
EINECS : 203-961-6
*See Section 16
| Chemical characterization | |
| Description | Mixture of substances listed below with nonhazardous additions. Cleansing agent |
| Dangerous components | non-ionic surfactants Xn, Xi; R 22-41 10-25 % CAS: 111-76-2 |
| EINECS | 203-905-0 2-butoxyethanol Xn, Xi; R 20/21/22-36/38 2.5-10% |
| General Information |
Immediately remove any clothing soiled by the product. Symptoms of poisoning may even occur after several hours; therefore medical observation for at least 48 hours after the accident. |
| After inhalation | Supply fresh air; consult doctor in case of complaints. |
| After skin contact | Generally the product does not irritate the skin. |
| After eye contact | Rinse opened eye for several minutes under running water. Then consult a doctor. |
| After swallowing | Call for a doctor immediately |
| Suitable extinguishing agents | CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam. |
| Protective equipment | No special measures required. |
| Person-related safety precautions | Wear protective clothing. |
| Measures for environmental protection |
Dilute with plenty of water. |
|
Do not allow to enter sewers/ surface or ground water. |
|
| Measures for cleaning/collecting |
Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). |
|
Dispose contaminated material as waste according to item 13. |
|
|
Ensure adequate ventilation. |
|
|
Dispose of the material collected according to regulations. |
| Handling | |
| Information for safe handling |
Store in cool, dry place in tightly closed receptacles. Prevent formation of aerosols. |
| Information about fire- and explosion protection | No special measures required. |
| Storage | |
| Requirements to be met by storerooms and receptacles | No special requirements. |
| Information about storage in one common storage facility | Not required. |
| Further information about storage conditions | None. |
Additional information about design of technical facilities: No further data; see item 7.
• Ingredients with limit values that require monitoring at the workplace: 111-76-2 2-butoxyethanol
WEL Short-term value: 50 ppm
Long-term value: 25 ppm
• Additional information: The lists valid during the making were used as basis.
• Personal protective equipment:
• General protective and hygienic measures: Keep away from foodstuffs, beverages and feed.
• Respiratory protection: Not required.
• Protection of hands: Protective gloves
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
• Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer.
• Penetration time of glove material
The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed.
• Eye protection: Safety glasses
• Body protection: Protective work clothing
• General Information
Form : Fluid
Colour : Yellowise / Clear
Odour : Characteristic
• Change in condition
Melting point/Melting range : Undetermined.
Boiling point/Boiling range : 171°C
• Ignition temperature : 240°C
• Self-igniting : Product is not selfigniting.
• Danger of explosion : Product does not present an explosion hazard.
• Explosion limits :
Lower : 1.1 Vol %
Upper : 10.6 Vol %
• Vapour pressure at 20°C : 23 hPa
• Density at 20°C : 1.01 g/cm³
• Solubility in / Miscibility with
water : Fully miscible.
• pH-value at 20°C : > 7
| Thermal decomposition / conditions to be avoided | No decomposition if used according to specifications.- |
| Dangerous reactions No dangerous reactions known. | |
| Dangerous decomposition products | Carbon monoxide and carbon dioxide. |
| Acute toxicity | Primary irritant effect: |
| on the skin | No irritant effect. |
| on the eye | No irritating effect. |
| Sensitization | No sensitizing effects known. |
| Additional toxicological information | The product shows the following dangers according to the calculation method of the General EU |
| Classification Guidelines for Preparations as issued in the latest version | Harmful |
| General notes | Water hazard class 2 (German Regulation) (Self-assessment): hazardous for water Do not allow product to reach ground water, water course or sewage system. Danger to drinking water if even small quantities leak into the ground. |
| Product Recommendation | Must not be disposed together with household garbage. Do not allow product to reach sewage system. |
| Uncleaned packaging Recommendation | Disposal must be made according to official regulations. |
| Recommended cleansing agents | Water, if necessary together with cleansing agents. |
• Land transport ADR/RID (cross-border)
• ADR/RID class : -
• Maritime transport IMDG:
• IMDG Class : -
• Marine pollutant : No
• Air transport ICAO-TI and IATA-DGR:
• ICAO/IATA Class : -
| Labelling according to EU guidelines | The product has been classified and marked in accordance with EU Directives / Ordinance on Hazardous Materials. |
| Code letter and hazard designation of product | Xn Harmful |
| Risk phrases | 22 Harmful if swallowed. |
| Safety phrases |
23 Do not breathe gas/fumes/vapour/spray (appropriate wording to be specified by the manufacturer). 26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. 36/37/39 Wear suitable protective clothing, gloves and eye/face protection. 60 This material and its container must be disposed of as hazardous waste. |
| National regulations | |
| Waterhazard class | Water hazard class 2 (Self-assessment): hazardous for water. |
This information is based on our present knowledge. However, this shall not constitute a guarantee for any
specific product features and shall not establish a legally valid contractual relationship.
• Relevant R-phrases
20/21/22 Harmful by inhalation, in contact with skin and if swallowed.
22 Harmful if swallowed.
36/38 Irritating to eyes and skin.
41 Risk of serious damage to eyes.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.