RXSOL-16-1003-020 is a highly concentrated for extremely high solvency and penetrating capabilities to remove carbonaceous Wetting Emulsifying Agent. Specifically formulated for removal of completely carbon, grease, oil, varnishes and other heavy deposits from diesel engine.

This powerful action is based on a two –Layer mechanism. The top-layer prevents the evaporation of the volatile components in the button-layer. The button –layer removes the deposited substances. This way, the deposits are bind and trapped resulting to complete and safe removal.

CARBON cleaner is very active which eliminates the need for Scrubbing or Brushing  which can cause mechanical damages to discs and result in poor performance

Technical Bulletin

CARBON REMOVER (RXSOL-16-1003-210)

Product Description:“RXSOL-16-1003-210” is a unique formulation of Wetting Emulsifying Agent alongwith powerful surfactants and  organic solvents.It does not contain any chlorinated solvents of Phenols & has less than 10% Aromatics & surfactants in the product do not contain any alkyl phenol ethoxylates.

Product Uses:
1.RXSOL-16-1003-210 is a fully active cleaner specially formulated  for the removal of“CARBON”& tuff oily stains residues.
2.CARBON cleaning is actived with out the need for Scrubbing or Brushing  which can cause mechanical damages to discs and result in poor performance.
3.Field test have shown that RXSOL-16-1003-210 is very gentle with personnel and on metallic colour surface.RXSOL-16-1003-210 should always be used at full strength to obtain maximum benefits.

Product-Application: Directions for Use and Dose Rates

Soak Method: The apparatus/parts for cleaning are dipped through the RXSOL-16-1003-210.Immersion time  will depend up on  the nature of the deposited particle.. The components should be rinsed   thoroughly before handling.

Dose: Either concentrate or dilute 1 part concentrate to 2-5 part water to yield a  very   effective end product  then components and machine parts are dipped into the solvent / solution  for  30 min.to 1-hour while for heavy deposition may need 12-24 hour.

Note : Low evaporation prevents loss  of chemical

Cleaning of Heat Exchangers(oil part)
1.Drain the system off any remaining oil.
2.Arrange the system for re circulation with active RXSOL-16-1003-210                                                                                                                                                3.Heat the Solń up to 50º.If heating is not available, the cleaning time will need to be extended.
4.Circulate for 12-15 hours. When the cleaning is complete drain the system.
5.Connecta high pressure fresh water supply to the upper heat exchanger connection.Rinse until water runsclear
6.Disconnect,drain and dry the system.

 Note:
– Cleaning time  will vary depending on the extract nature and thickness of deposit  to be removal.
– Stubborn deposits should be scrubbed to assist the cleaning operation
– Your local Rx Cleansers representative will work with you to design the optimum concentrati-on&procedure
   for your system.

Safety And Handling : “RXSOL-16-1003-210 ” is completely safe to handle, being non-toxic & non corrosive.As with all chemicals general safety and handling procedures apply. Avoid contact with eyes as irritation may occur. Do not take internally. In case of contact with eyes, flush eyes immediately and cupiously with clean running  water for 15- minutes and seek medical attention.

Product Properties:-

Characteristics : (RXSOL-16-1003-210)
. Unique chemical formulation
. Non- toxic
. Extends time between cleans.
. Safe to handle
. Effective removal of STICKER/CARBON DEPOSITS.
. Can be applied by all normal methods.
. Formulated to be very cost effective.
. Does not contain chlorinated hydrocarbons.
. Can be used on all metals & most painted surfaces.
. Environmentally friendly.
. Non-Corrosive.
. 93-98% Active.
. Dries Completely.
. Does not require special feeding equipment for safe application.
. Reduce downtime and maintenance costs

Product Label

RXSOL-16-1003-020 is a highly concentrated Wetting Emulsifying Agent.Specifically formulated for removal of completely carbon, grease, oil, varnishes and other heavy deposits from diesel engine
This powerful action is based on a two –Layer mechanism. The top-layer prevents the evaporation of the volatile components in the button-layer. The button –layer removes the deposited substances. This way, the deposits are bind and trapped resulting to complete and safe removal.

CARBON cleaner is very active which eliminates the need for Scrubbing or Brushing which can cause mechanical damages to discs and result in poor performance